Bedienungsanleitung Rotel RT-06 (Seite 10 von 89) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490029

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

RDV-1092

RT-06 DAB/AM/FM Stereo Tuner

NUMERIC Buttons: Station

Presets

The RT-06 can store up to 30 station presets

for recall at any time using the NUMERIC

keypad. These station presets can be used

of any combination of AM stations as well

as 99 station presets for DAB.

The RT-06 is delivered from the factory with

a set of generic station preset that may or

may not match any available stations in

your area.

To memorize a new station preset:

1. Tune to the desired station, AM or FM.

2. Press the MEMORY button on the front

panel. A MEMORY indicator will ﬂash in

the front panel display.

3. While the MEMORY indicator is ﬂashing,

press the number of the preset where you

wish to store the station frequency. For ex-

ample, to memorize the station as preset

3, press the 3 button. To memorize preset

15, press the 1 button followed by the 5

button.

4. A previously stored frequency is erased

from memory when a new frequency is

memorized for the same preset number.

To tune to a previously memorized station

preset, press the preset number using the

NUMERIC buttons. For example, to tune to

preset 3, press the 3 button. To tune to preset

30, press the 3 button and then press the 0

button within 5 seconds.

NOTE: The NUMERIC buttons can also be

used for FREQUENCY DIRECT tuning with

the AM/FM band.

FREQUENCY DIRECT

Button:

Direct Access Tuning

If you know the exact frequency of the de-

sired station, you may tune it directly using

the FREQUENCY DIRECT button and the

NUMERIC buttons.

1. Press the FREQUENCY DIRECT button to

change the NUMERIC buttons from station

preset to direct access mode. The station

frequency in the front panel display will

change to a series of bars, representing

the digits of a station frequency, with the

ﬁrst bar blinking.

2. Enter the ﬁrst digit of the station frequency

using the NUMERIC buttons. The digit will

appear in the frequency display and the

next bar will ﬂash. Enter the remaining

digits of the frequency. When all of the

digits have been entered, the tuner will

automatically tune to the displayed station

frequency.

NOTE: On the USA version only, pressing 1 in

the FM mode will enter 10 as the digit in the

frequency display. On the European version,

it is necessary to press 1 and then 0 to enter

10. For US FM station, press only one digit

following the decimal point as shown in the

ﬁrst example below. For European FM sta-

tions, press two digits after the decimal point

as shown in the second example.

EXAMPLES:

• (USA FM) 87.50MHz Press 8>7>5

• (Europe FM) 87.50Mhz Press 8>7>5>0

• (USA AM) 1610kHz Press 1>6>1

• Europe AM) 1611kHz Press 1>6>1>1

If no frequency is entered within 5 seconds,

the tuner will cancel FREQUENCY DIRECT

tuning mode and revert to the last previously

tuned station.

AUTO TUNING Button

The AUTO TUNING button toggles between

the frequency search tuning feature and

manual frequency tuning. When using the

TUNING controls on the front panel or re-

mote in AUTO TUNING mode, the tuner will

begin automatically scanning up or down

through the frequencies until the next receiv-

able broadcast signal is detected. If this is

not the desired station, use the TUNING

controls again to ﬁnd the next station. Weak

stations will be skipped during auto tuning.

If no receivable signal is detected, the tuner

will revert to the previously tuned station. To

toggle between FREQUENCY TUNING mode

and AUTO TUNING mode, press the AUTO

TUNING button. An AUTO indicator will ap-

pear in the display.

NOTE: AUTO TUNING mode is disengaged

when the TUNE/PRESET button is set to

PRESET tuning mode. See the following

section.

TUNE/PRESET Button

The TUNE/PRESET button toggles between

FREQUENCY TUNING mode (the TUNING

controls advance to the next station frequency)

and PRESET TUNING mode (the TUNING con-

trols advance to the next memorized station

preset.) To toggle between the two modes,

press the TUNE/PRESET button. A PRESET

indicator in the front panel DISPLAY will light

when the PRESET mode is active.

NOTE: AUTO TUNING mode is disengaged

when the TUNE/PRESET button is set to PRE-

SET tuning mode.

PRESET SCAN Button

This button activates a preset scanning fea-

ture. When you press the button, the tuner

will automatically scan through all memorized

station preset, playing each for ﬁve seconds

before moving to the next. To stop the station

scanning on the desired station preset, press

the button again.

NOTE: If a preset station is currently tuned

when the PRESET SCAN button is pressed,

scanning will start with the next higher pre-

set number and continue through all preset

stations, stopping on the initial preset. If a

PRESET station is not currently tuned when

the button is pressed, scanning will start from

PRESET 1 and continue to PRESET 30.

FM MONO

The FM MONO button changes the FM

mode from stereo reception to mono recep-

tion. In stereo mode, a stereo signal will be

heard if the station is broadcasting a stereo

signal and there is sufﬁcient signal strength.

A stereo indicator will light in the front panel

display. In mono mode, a mono signal will

be heard even if the station is broadcasting

a stereo signal.

NOTE: Switching to mono mode can be a

useful way to improve the reception of weak

or distant FM signals. Less signal strength is

required for clean mono reception than for

stereo reception.

Rotel RT-06 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info