Bedienungsanleitung Rowenta DX 9300 (Seite 4 von 5) (Englisch)

483579

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Before use

Before doing anything else, remove the soleplate protector!

Before ironing for the first time heat the appliance at the

maximum setting (see D "Setting the temperature").

A little smoke and a slight smell may be emitted, but this

is only temporary. The water tank can then be filled

directly (see C "Filling with water/topping up").

Before ironing for the first time and after filling and hea-

ting up, the iron should be allowed to emit steam for at

least 1 minute to remove any impurities.

Filling/topping up water

Before filling the water tank, pull out the mains plug and

set the steam control to position .

Tilt the iron. The filler inlet can easily be opened by

pressing the push-button. The inlet will open with a

"click". Pour in water up to the max (9) mark. Close the

filler inlet by pressing the push-button again, before

returning the iron to the horizontal.

What water may be used ?

Your iron has been designed to operate using tap water.

However, if your water is very hard, you can mix it 50%

tap water with 50% distilled or demineralised water.

Do not add anything to the contents of the water tank

and do not use water from clothes dryers, scented or

softened water, water from refrigerators, batteries or air

conditioners, pure distilled water or rain water. These

contain organic waste or mineral elements that become

concentrated when heated and cause spitting, brown

staining or premature water to your iron.

Setting the temperature

D1 Electronic temperature control (Thermo Control)

On your electronic iron you can set the precise ideal tem-

perature for each material. The different types of material

are shown on the temperature control dial:

The soleplate of your iron is fitted with an electronic sen-

sor which continuously monitors the temperature of the

soleplate and keeps it at the precise selected setting. This

enables you always to iron at the optimum temperature.

D2 LED ”TRAFFIC LIGHT“ DISPLAY

The traffic lights tells you whether the soleplate is at the

selected temperature (see table below).

Tip: We recommend that you start with fabrics to be ironed

at a low temperature as the iron takes longer to cool

down than to heat up. For mixed fabrics set the tempe-

rature for the most delicate fabric.

Ironing and Steam functions

E1 Dry ironing

To iron without continuous steam, turn the steam control

to and set the temperature to suit the type of material

(care points •, ••, •••).

E2 Steam ironing

You can steam iron from temperature setting •• up. The

steam quantity can be set to between (minimum steam

quantity) and (maximum steam). We recommend setting

to maximum steam quantity only when the iron is at

temperature setting •••.

E3 Intra Steam

Your iron is fitted with the new Intra Steam system. This

technology generates higher steam pressure to enable the

steam to penetrate much faster and further into the fabric.

This way you get excellent results from your ironing.

The steam is emitted in frequent bursts rather than conti-

nuously. The pressure generated may cause a slight noise.

This is not a technical fault!

E4 Power steam button (from temperature setting •• up)

To generate a powerful jet of steam and remove stubborn

creases, press the power steam button.

Vertical steam ironing (from temperature setting •• up)

Ideal for removing creases from suits, jackets, skirts,

hanging curtains etc.

Important:

Never steam or iron clothing that is being worn!

- Hang up the garment on a hanger and hold the fabric

slightly taut with one hand.

- Set the thermostat control to maximum steam

- Hold the iron a few centimetres away from the garment

to avoid burning delicate fabrics.

- Press the power steam button repeatedly, moving the

iron from top to bottom.

LED display

You can start ironing

now. The soleplate is at

the optimum tempera-

ture for your material.

Wait for the iron to cool

down to the selected

temperature and the

LED display to switch

to GREEN.

You can start ironing

now, but the soleplate

is not yet at the selec-

ted temperature.

What to do

The soleplate is

at the right tem-

perature for the

selected material.

The soleplate is

still too hot for

the selected

material.

The soleplate is

still too cold for

the selected

material.

This means:Colour

YELLOW

GREEN

RED

Innen - DX9200_7 08.04.2003 9:32 Uhr Seite 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta DX 9300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info