Bedienungsanleitung Rowenta DX 9300 (Seite 5 von 5) (Englisch)

483579

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

The power steam and vertical steam functions (E 4) are

also possible if the steam control is set to . The interval

between bursts of steam should be about two seconds.

Important:

Never direct the steam at persons or animals!

E5 Spray function

To dampen stubborn creases, press the spray button.

Additional functions

F1 Anti-Drip system

Prevents water escaping from the soleplate when the

temperature is too low.

F2 Anti-scale system

Your iron contains an anti-scale cartridge to reduce scale

deposits. This considerably prolongs the operational life

of your iron. The anti-scale cartridge is an integral part of

the water tank and need not be replaced.

Do not use descaling agents, as these damage the lining of

the steam chamber and so may impair the steam function.

F3 Automatic electronic 3-position cut-out (depending on

model)

If, although switched on, the appliance is not moved, it

will automatically switch off after the following intervals:

After 30 sec., if the iron is standing on the soleplate or

lying on its side.

After 8 mins., if the iron is standing on its heel.

The LED display starts to flash yellow-green-red in regular

sequence. If the appliance is moved, it will automatically

switch on again and begin to heat up again.

After ironing

• Unplug from the mains, pour away remaining water

and set steam control to . Then allow the appliance to

cool down.

• Store the iron standing on its heel.

• Do not wind the cord round the hot soleplate.

Cleaning and maintenance

When the appliance has cooled down, wipe it down with

a damp cloth or sponge, as required.

Dirt can be removed from the soleplate with a damp

cloth or sponge. Do not use sharp or abrasive cleaning

agents or objects.

Important: If the appliance has been standing unused for

long periods, hold it horizontal and allow it to emit

steam for approx. 1 minute to clean the steam ducts and

remove any residue from the iron.

Problems?

If you have any further problems or queries with our products

please call our Customer Relations team first for expert help and

advice:

HELPLINE:0845 602 1454 – UK, 01 4751947 – Ireland

If you are unable to trace the cause of the fault, contact an

official Rowenta Customer Service Centre. The addresses are

shown in the enclosed service centre address list. Further hints

and tips are obtainable from our homepage: www.rowenta.com.

In line with a policy of continuous product improvement

Rowenta reserves the right to change product specifications

without prior notice.

Problems

The iron is plug-

ged in, but the

soleplate of the

iron remains cold.

The soleplate is

not heating up

properly.

LED „Traffic Light“

display does not

light up.

None or too little

steam is being

emitted.

All 3 colours of

the Traffic Light

display flash

alternately.

The traffic Light

display flashes

red fast.

Brown streaks

come through the

holes in the sole-

plate and stain

the fabric.

The soleplate is

dirty or brown

and can stain the

linen.

The soleplate is

scratched or

damaged.

No mains supply.

The temperature

control is set too

low.

Temperature con-

trol set to "0".

There is insuffi-

cient water in the

water tank.

Anti-Drip is active

(F1).

The automatic cut-

out has activated:

the appliance is

on standby.

The temperature

sensor in the sole-

plate is defective.

You are using che-

mical descaling

agents.

You linen is not

rinsed sufficiently

or you have ironed

a new garment

before washing it.

You are using a too

high temperature.

You are using

starch.

You have placed

your iron flat on a

metallic rest-plate.

You have ironed

over a zip.

Check that the mains plug is

properly inserted or try

plugging the iron into a dif-

ferent socket.

Set the temperature control

to a higher temperature (D).

Turn the temperature control

to the required setting.

Fill the water tank (C).

Wait for the soleplate to reach

the correct temperature.

If moved, the appliance will

switch on again.

Call our Customer Relations

Helpline – see below

Do not add any descaling

agents to the water in the

water tank.

Ensure linen is rinsed

thoroughly to remove any

soap desposits or chemicals

on new garments which may

be sucked up by the iron.

See the temperature table to

correctly set the thermostat.

Clean the soleplate as indi-

cated above. Always spray

starch onto the reverse side

of the fabric to be ironed.

Always set the iron on its

heel.

Try to avoid ironing over zips

which may have rough edges.

Possible cause Solution

Innen - DX9200_7 08.04.2003 9:32 Uhr Seite 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta DX 9300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info