Bedienungsanleitung Rowenta DX8300 (Seite 5 von 7) (Englisch)

483581

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Filling the water tank

Before filling the water tank, unplug from the mains and set the steam

control to the Dry position .

To open the water filling inlet, push the cover downwards, tilt the iron

and pour in untreated tap water up to the maximum level ( ). Close

the cover before holding the iron horizontal again.

What water may be used?

Your iron has been designed to operate using untreated tap water.

However, if your water is very hard, you can mix it 50% tap water with

50% distilled or demineralised water.

Do no add anything to the contents of the water tank and do not use

water from clothes dryers, scented or softened water, water from refri-

gerators, batteries or air conditioners, pure distilled water, rain water,

boiled water, bottled water or filtered water. These contain organic

waste or mineral elements that become concentrated when heated and

cause spitting, brown staining or premature wear to your iron.

Tip: Spray starch onto the reverse side of the fabric to be ironed to

avoid stains on the soleplate.

Setting the temperature

Using the temperature control ( ), set the iron temperature to suit the

type of material. We recommend using the above table as a guide. The

thermostat light ( ) indicates that the soleplate is heating up. When

the light goes out, the required temperature has been reached.

Please note: When heating up the iron from cold, wait until the ther-

mostat light has gone out a second time. Only then is the set

temperature reached.

Tip: We recommend that you start with fabrics to be ironed at a low

temperature as the iron takes longer to cool down than to heat up.

For mixed fabrics set the temperature for the most delicate fabrics.

Ironing and Steam functions

E1 Ironing with Dry Position (without steam)

To iron without continuous steam and for perfect finishing results turn

the steam control ( ) to the Dry Position . It will engage with a

“Click”. Set the temperature to suit the type of material

(care points

•, •• or •••).

E2 Steam ironing

You can iron with continuous steam by setting the temperature dial

( ) in the marked steam zone (after

••

). The steam quantity can be set

between minimum (see drawing E2, smallest dot) and maximum

steam . We recommend setting to maximum steam quantity only

when the iron is at maximum temperature setting to avoid droplets of

water leaking from the soleplate.

E3 Extra Long Shot button (temperature setting at maximum)

Your iron is equipped with a new special Extra Long Shot, which

allows you to iron out creases perfectly, specifically on dry and thick

fabrics. By pressing the Extra Long Shot button ( ) steam is pushed

with more pressure into the fabrics, because of this new technology.

The steam reaches a bigger area and penetrates much deeper into

fabrics. So you get excellent results from your ironing.

The pressure generated may cause a slight noise. This is not a

technical fault!

The Extra Long Shot (E3) is also possible to use if the steam control is

set to the Dry Position .

Ironing label Fabric

Synthetic fibres e.g.

viscose, polyester

silk, wool

cotton, linen

Temperature control

DX8000-7spr 21.10.2004 10:29 Uhr Seite 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta DX8300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info