Bedienungsanleitung Ruby Fires RF30 (Seite 12 von 28) (Deutsch, Englisch, Holländisch, Französisch)

589955

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation Instructions

Before installing this appliance in an existing chimnney, we recommend that;

1. You have your chimney cleaned by a competent chimney sweep.

2. You block o the chimney  ue.

This procedure is important for the e cient operation of the heating unit and will also reduce heat loss up the chimney.

Installation.

Ensure that all packing items are removed (read any warning labels carefully).

Retain all packing for possible future use e.g. in the event of moving or returning the appliance to your supplier.

To install the appliance;

1. Clean the area where the  re will be installed e.g remove ash residue from an existing  replace.

2. Use the two adjustable supports at the rear of the appliance to ensure that the  re is level.

3. Make sure the unit is switched OFF.

4. Hold the  re by the sides of surround and gently manoeuvre into position. Plug the  re into a 13amp/240 volt outlet. Ensure

that the supply cable is not trapped under the  re such that it might cause it to be damaged.

Before using the manual controls  rstly  ll the water tank (See ‘Maintenance’, ‘Filling the water tank’).

Manual Controls.

The Mystic Fires manual controls are located beneath the hinged canopy. Raise the canopy to access the controls. (See Fig.2

for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate either with or without heat.

Switch ‘B’:- Press

once to turn on the  ame e ect. This will be indicated by an audible beep. Although the main lights

operate immediately it will take a further 30 seconds before the  ame e ect starts.

Press again to give  ame e ect and half heat. This will be indicated by two beeps.

Press again to give  ame e ect and full heat. This will be indicated by three beeps.

Press again to return to  ame e ect only. This will be indicated by one beep.

Press to put  re in to standby mode. This will be indicated by one beep.

Control Knob ‘C’:- Controls the Thermostat setting.

Turning the control knob Anti Clockwise will decrease the temperature setting, turning the control knob Clockwise

will increase the temperature setting.

Control Knob ‘D’:- Controls the intensity of the  ame e ect.

Turning the control knob Anti Clockwise increases the  ame e ect, turning the control knob Clockwise will decrease

the  ame e ect.

When the water in the tank and in the sump runs out the main lamps will go out. See instructions under ‘Maintenance’, ‘Filling

the water tank’. When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the  ames

return.

Setting the Thermostat

Plug in and switch on the  re to the full heat setting. Turn the Control Knob ‘C’ fully clockwise (max temperature setting) to

warm the room rapidly. When the room temperature has reached the desired level, turn the thermostat knob back slowly until

you hear the thermostat just click o . The heater will then maintain the room temperature at the chosen level.

Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room temperature

being higher then the thermostat setting

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if the heat

outlet was restricted in any way or if the chimney  ue has not been blocked o e ectively. If the cut-out operates, unplug the

heater from the socket outlet and allow approximately 10 minutes before reconnecting. Before switching the heater back on

remove any obstruction that may be restricting the heat outlet, then continue normal operation.

Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied

through an external switching device, such as a timer, or connected to a switch that is regularly switched on and o by the

utility.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ruby Fires RF30 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info