Bedienungsanleitung Ruby Fires RF30 (Seite 13 von 28) (Deutsch, Englisch, Holländisch, Französisch)

589955

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Tips for using your appliance.

1. With the  ame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long than

when it is at maximum  ame setting.

2. Do not tilt or move the  re while there is water in the tank or sump.

3. Make sure that the  re is on a level  oor.

4. The  ame control knob ‘D’ Fig.2 may be turned up or down to give a more realistic e ect.

5. Sometimes the  ames appear more real when the  ame control knob is turned down.

6. Give the  ame generator some time to react to changes you may make on the  ame control knob.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE BEGINNING ANY MAINTENANCE

Changing lamps.

If the smoke appears grey or colourless it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the  ame e ect on, lift out the fuelbed and water tank. (See Fig.3)

2. It should be possible to view the lamps with the nozzle (See Fig.4) in place and observe which one needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the  re from the mains.

4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.

5. Remove the sump as described in the Cleaning Section.

6. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (See Fig.4 and 4a).

Replace with a 12V, 45W, Gu5.3 base, 8º beam angle, coloured lamp.

7. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push  rmly in place. (See Fig.4 and 4a).

8. Replace the sump, nozzle, water tank and fuelbed.

9. Switch on.

Filling the water tank.

When the water tank is empty, the  ame and smoke e ect shuts o and you will hear 2 audible beeps, follow these steps.

1. Press Switch ‘A’ to (0) (See Fig.2)

2. Gently lift out the fuelbed and set aside carefully. (See Fig.3)

3. Remove the water tank by lifting upwards and outwards.

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig.5)

5. Fill tank with  ltered tap water only. This is necessary to prolong the life of the  ame and smoke producing unit.

The water should be  ltered through a conventional domestic water  lter unit and the  lter should be replaced regularly.

6. Screw the cap back on, do not overtighten.

7. Return the tank to the sump, with the tank cap facing down and the  at side of the tank facing outward.

8. Gently place the fuelbed back into position.

9. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig.2)

Cleaning.

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump, Nozzle, Tank cap and seal, Air  lter.

For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or  u the soft

brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater.

Water tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer

groove and the centre rubber seal.

3. Put a small quantity of washing up liquid into the tank, re t the cap and shake well, rinse out until all traces of washing up

liquid are gone.

4. Re ll with  ltered tap water only, replace the cap, do not overtighten.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position

2. Gently lift out the fuelbed and place carefully on the ground. (See Fig.3)

3. Remove the water tank by lifting upwards.

4. Disconnect the electrical connector, located on the right side of the sump. (See Fig.6) .

5. Release the right sump locking tabs by turning 90º, this allows the sump to be lifted completely from its location.

(See Fig.6a)

6. Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in the sink.

7. Release the left sump locking tabs by turning 90º, then lift o the Nozzle. (See Fig.4)

8. Lift out the transducer and carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig.8)

9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces in the sump

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ruby Fires RF30 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info