Bedienungsanleitung Rupes P850E (Seite 7 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489891

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Position A= lowest speed

Position G = highest speed

Ensure that the drill is not allowed to jam for

longer than 2-3 seconde. Longer jamming can

lead to motor damage.

Important!

Continuous operation under strong load and

low speed can overheat the motor.

Allow the motor to cool down in no-load when

set at a high speed!

8. CHANGING DIRECTION OF ROTATION

(main rotation - clockwise)

Direction of rotation of the drill spindle is changed

using the reversing switch (3).

R = Clockwise (Right)

L = Anticlockwise (Left)

Important!

Presa the reversing switch until it reaches the

respective end position at the housing, i. e.

until it can be felt to engage!

The reversing switch is easiest to operate by

using the thumb and index or middle finger from

both sides.

Attention!

Change direction of rotation only when the

motor has ceased turning! When using the

drill as a screwdriver, the percussion mecha-

nism must be switched off. Switch-over by

means of the sliding switch (4).

When in middle position, the reversing switch

prevents the accidental activation of the full

wave electronic switch (1), for example when

changing tools or assembling/disassembling

the drill chuck.

9. PERCUSSION DRILLING DEVICE

The machine has an integrated percussion

mechanism and can be switched from normal

drilling to percussion drilling. The sliding switch

(4) allows switching from normal drilling to per-

cussion drilling or vice-versa while the machine is

in operation.

Normal drilling position:

Move switch (4) to the right in direction of normal

drilling.

Percussion drilling position:

Move switch (4) to the left in direction of percus-

sion drilling.

10. MECHANICAL 2-SPEED SELECTOR

The speed is selected by turning the selector dial

(5).

Position 1 = low speed

Position 2 = high speed

2-speed gearing gives the percussion drill added

versatility. The fast speed (position 2) is adjusted

for percussion drilling and nonnal small-hole drilling

up to a drill bit diameter of ap¬proximately 8 mm.

The slow speed (position 1) is adjusted for larger

drill bit diameters and for stirring applications.

11. THE SAFETY SLIPPLING CLUTCH

The slipping clutch begins to operate as soon as

the drill or the tool being driven is overloaded,

violently braked or jammed. The motor and tran-

smission continue to rotate, but the tool is no lon-

ger driven. This protects the driveline against

overloads and avoids damage to the gear teeth

caused by violent shocks.

12. CHUCK

The chuck is tightened with a turning moment

of 30 Nm. Only this guarantees that the chuck is

not unintentionally unwound from the drill spindle

in anticlockwise mode. Should the chuck be

undone from the drill spindle for the purpose of

replacement, the new chuck must be tightened

with a turning moment of at least 30 Nm before

the machine is used again.

The piane surfaces of the chuck and drill spindle

must be cleaned before a new chuck is mounted.

Caution!

Before disassembling and reassembling the

drill chuck, disconnect the machine from the

power supply, or remove the mains cable

module (6) from the grip using the locking

device button (7).

Caution!

When turning anticlockwise, it is possible

that the chuck loosens itself from the spindle.

For this reason make sure that the chuck sits

properly on the spindle.

13. OPERA

TING THE QUICK-CHANGE

CHUCK

This chuck has been developed especially for

use with percussion drills.

The fully-automatic spindle locking device ena-

bles a quick and problem-free tool change in the

chuck.

librettoP850E 21-08-2007 9:26 Pagina 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rupes P850E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info