Bedienungsanleitung Rupes P850E (Seite 8 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489891

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

The drill spindle will be automatically fixed when

the chuck is actuated.

The chuck has a release safety lock which pre-

vents any unintentional release of the drilling tool

even at high impact frequencies.

After attaching the jaw chuck to the tool, a slightly

higher torque must be used to engage the clam-

ping force safety lock. The torsion angle of the

collar must be approximately 50° during the loc-

king procedure. After this has been completed,

the tool can be tensioned as usual. Turn the col-

lar firmly in the "ZU" direction until a click is

heard. The drill is only properly tensioned when

the collar has been turned as far as possible and

no more clicking is heard.

14. USE AS ASCREWDRIVER

Screwdriver inserts (bits) can fitted directly into

the chuck. Use Phillips screws for best results.

Safe operation is ensured by the self-centering

mechanism. Please make sure to use the correct

screwdriver inserts.

15. CUTTING THREADS

The integrated electronic and the reversal of the

direction of rotation makes the percussion drill

also suitable for cutting threads. The use of

machine taps is recommended. The tap is clam-

ped into the chuck.

The electronic controls are sensitive and should

be handled with utmost care to prevent any brea-

king of tap - particularly when cutting threads into

blind holes. The required torque may be selected

via the adjusting wheel in switch (1).

Important! When cutting threads, use Iow

speeds only.

Always make sure that the chosen speed is

correct for the purpose for which you are

using the machine.

High speeds are necessary for polishing and

grinding. When drilling match speed with type of

material and drill. High speed drilling in steel and

stone will cause premature tool wear

Use tool steel twist drills for soft materials such

as wood and plastics; carbide-tipped stone drills

for stone and concrete; high speed twist drills for

steel and iron.

Also make sure that, using a gear-rim chuck,

the drill chuck key is never fastened to the

drill with chains, strings or by similar means.

Be sure that the workpiece cannot be taken

along by the drill.

16. MAINTENANCE

The machine's motor has life-time lubrication and

requires no special maintenance. However,

should you operate the machine on a continuous

basis over long periods of time we recommend

that you send us the machine for thorough clea-

ning and an inspection. This will spara you unne-

cessary repair expenses and increase the machi-

ne's service life. If you always clean the ventilator

of dust after each operation, the motor will enjoy

an ever longer service life. Uniform ventilation is

essential for a long service life.

17. REPLACING CARBON BRUSHES

Our service personnel will do this and all other

servicing work fast and professionally.

18. MAINS CABLE

Damaged mains cables must not be used. They

are to be replaced immediately.

Thanks to the innovative mains cable with patent

quick release lock (6) it is possible for you to

replace the cable with the greatest of ease. Press

the two lock pushbuttons (7) and pull the mains

cable out of the casing (6). Feed the new mains

cable into the hand grip until it snaps in piace.

Various cable lengths are available upon request.

Only use the mains cable module for Rupes

power tools! Do not attempt to operate other

electrical appliances with it!

19. AUXILIARY HANDLE

For safety reasons the side handle should always

be used when working with the percussion drill. It

guarantees safe, wander-free guidance of the

drill, and at the same time precise adjustment of

the drilling depth with the depth stop. Operate the

machine only with the auxiliary handle 9 . Mount

the handle onta the clamping collar of the drill,

turning it to the working position and tightening it

using the handle collar.

20. STANDARD ACCESSORIES

Side handle with depth stop.

21. INFORMAZIONI RELA

TIVE A RUMORE E

VIBRAZIONI

Measured values deterrnined according to EN 60

745.

Typically the A-weighted noise levels of the

machine are: sound pressure level 98 dB (A);

sound power level 109 dB (A). Measurement

uncertainty K = 3 dB.

Wear hearing protectionl

The typically weighted acceleration is 6.83 m/s

librettoP850E 21-08-2007 9:26 Pagina 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rupes P850E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info