489931
9
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
Quick-action chuck with ASL
If the On/Off switch 2 is not pressed, the drill spindle and thus the tool
holding fixture are locked.
Inserting the tool
- Turn the clamping sleeve anticlockwise to open the clamping jaws.
- Insert the tool into the chuck.
- Clamp the tool in position by turning the
clamping sleeve clockwise.
- Tighten the sleeve of the quick-action chuck firmly by hand until it
no longer "clicks“.
Always pay attention that the tool is properly centred in the chuck.
Removing the tool
- Open the clamping sleeve in anticlockwise direction until the tool is
released and can be removed.
OPERATING TIPS
Drilling
Always select the speed to suit the material in question and the drill
bit diameter.
Fixing screws
Apply the power tool to the screw only when it is switched off.
Rotating tool inserts may slip. Before screwing larger, long screws
into hard materials, it is advisable to predrill a pilot hole with the core
diameter of the thread to approx. 2/3 of the screw length. Make sure
that the bit and screw correspond in size and shape. Optimal scre-
wing is achieved when the bit is fixed securely in the screw head.
Thread cutting
We recommend the use of machine thread taps.
- Lightly oil the thread tap.
- Cut in clockwise direction, stop, remove in anticlockwise direction.
NOTE
Always work at low speed when thread cutting. This prevents the
thread tap breaking off.
TOOLS AND ACCESSORIES
For metal, use only flawless, sharpened drills; for stone and concre-
te, only rock drills with hard metal inserts.
Screw tools
When using screwdriver bits, always use a bit holder. Use only
screwdriver bits that fit the screw head.
Changing the tool holder
Before carrying out any work on the machine, pull the mains plug. All
conventional chucks with internal thread (opening width max.10 mm)
can be used. Thread admission 3/8 - 24UNF.
Locking screw
Chuck fixed in place with locking screw.
- Remove the left-hand threaded screw which secures the chuck on
the drill spindle against unscrewing during anti-clockwise rotation.
- Replace the locking screw when you have fitted the chuck.
Removing the drill chuck
- Place the power tool on a stable base.
- Mount an Allen key in the drill chuck and fix a fork wrench on the
drill chuck at the front. At the same time, fix a fork wrench on the
wrench surface of the drive spindle.
- Fix the drive spindle and loosen the drill chuck by turning the Allen
key or fork wrench in an anticlockwise direction.
A tight drill chuck is loosened by tapping gently on the long shaft of
the Allen key or fork wrench.
- Remove the tools and unscrew the drill chuck completely.
Fitting the drill chuck
- Clean thread on drill chuck and drill spindle.
- Screw the drill chuck 1 onto the drill spindle.
The drill chuck must be tightened with a starting torque of 15 Nm.
- Secure the chuck with glue or the locking screw.
NOTE
Do not fix drill chuck wrench on the drill with chains, strings or simi-
lar means. The drill chuck wrench could get caught in moving parts
and lead to injuries.
Special accessories
Do not use accessories made by other manufacturers, as these are
not tested by us. It can be dangerous to use such accessories. To
avoid injury and damage, use only accessories recommended by us.
MAINTENANCE AND SERVICE
Maintenance and Cleaning
Before carrying out any work on the machine, pull the mains plug.
- Always keep the machine and ventilation slots clean.
- Wipe off the accessible plastic parts regularly with a cloth without
cleaning agent.
- Always keep the tool holder clean.
Replacing brushes
Worn carbon brushes should be replaced by an authorised customer
service organisation.
SERVICE
After heavy use over a long period, the machine should be taken to a
service location for inspection and thorough cleaning.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing them as
waste. The machine, accessories and packaging should
be sorted for environmental-friendly recycling. The plastic
components are labelled for categorised recycling.
Only for EC countries. Do not dispose of electric tools together with
household waste material! In observance of the European Directive
2002/96/EC for waste electrical and electronic equipment and its
implementation in accordance with national law, electric tools that
have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
GUARANTEE
All tools manufactured by RUPES Spa are guaranteed for 12 months
from the date of purchase against fabrication and material defects. All
tools must be used only with RUPES original accessories and spare
parts: we refuse all responsibility for damages or accidents caused
by non-observance of this rule which will also cause the termination
of the guarantee. The guarantee will no longer be valid if the instruc-
tions contained in this booklet are not followed, if the tool is used for
purposes other than that for which it is intended, if it is dismantled,
interfered with in any way or damaged due to neglect. The guarantee
will be made valid by filling-in the form on the inside back cover of
this instruction booklet. If the tool is found to be defective or mal-
functions, it should be returned carriage free in one piece in its origi-
nal packing together with the guarantee certificate to the manufactu-
rer or to one of the Assistance Centres listed in the appendix to this
booklet. The guarantee does not automatically imply replacement of
the tool. RUPES Spa reserves the right to make any technical or
design modification to its products without prior notice. The manu-
facturer is not liable for any print errors. This document voids and
replaces previous ones.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Rupes TR101 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info