Bedienungsanleitung Ryobi ccs 1801dm one (Seite 17 von 209) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383094

Zoom out

Zoom in

Vorherige Seite

1/209

Nächste Seite

CIRCULAR SAW SAFETY

■ Check the lower guard for proper closing before

each use. Do not operate sawif lower guard does

notmove freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

■ Check the operation and condition of the lower

guard spring. If the guard and the spring are not

operating properly, they must be serviced before use.

Lower guard may operate sluggishly due to damaged

parts, gummy deposits, or a buildup of debris.

■ Lower guard should be retracted manually only

for special cuts such as "Pocket Cuts" and

"Compound Cuts". Raise lower guard by Retracting

Handle. As soon as blade enters the material, lower

guard must be released. For all other sawing, the

lower guard should operate automatically.

■ Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to

stop after switch is released.

■ Do not use blades which are deforemed or cracked;

■ Do not use saw blades made of high speed steel;

■ Do not use blades which do not comply with

characteristics specified in these instructions;

■ Do not stop the blade by lateral pressure on the disc;

■ Ensure that movable guards, operate freely without

jamming;

■ Do not lock the movable guard in the open position;

■ Ensure that any retraction mechanism of the guard

system operates correctly;

■ Do not use saw blades the body of which is thicker or

set of which is smaller than the thickness of the

riving knife.

SAFETY INTRUCTIONS FOR CIRCULAR SAW

WITH RIVING KNIFE

■ Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must be

thicker than the body of the blade but thinner than the

tooth set of the blade.

■ Adjust the riving knife as described in this

instruction manual. Incorrect spacing, positioning

and alignment can make the riving knife ineffective

in preventing kickback.

■ Riving knife causes interference during plunge cutting

and can create kickback.

■ For the riving knife to work, it must be engaged in

the workpiece. The riving knife is ineffective in

preventing kickback during short cuts.

■ Do not operate the saw if riving knife is bent. Event a

light interference can slow the closing rate of a guard

CAUSE OF KICKBACK

■ Kickback is a sudden reaction to a pinched, bound,

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward

the operator.

■ When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator.

■ If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into

the top surface of the wood causing the blade to climb

out of the kerf and jump back toward the operator.

■ Kickback is a result of tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precaution as

given below.

PREVENTION OF KICKBACK

■ Maintain a firm grip with both hands on the saw

and position you arms to resist kickback forces.

Position your body to either side of the blade,

but not in lime with the blade. Kickback could

cause the saw to jump backwards, but kickback

forces can be controlled by the operator, if proper

precautions are taken.

■ When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to

a complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the

blade is in motion or KICKBACK may occur.

Investigate and take corrective actions to eliminate the

cause of blade binding.

■ When restarting a saw in the workpiece, center

the saw blade in the kerf and check that teeth are

not engaged into the material. If saw blade is

binding, it may walk up or KICKBACK from the

workpiece as the saw is restarted.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

CCS-1801DM 1/06/05 14:53 Page 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi ccs 1801dm one Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info