Bedienungsanleitung Ryobi EWS-1366 (Seite 18 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

491257

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ATTACHING AND REMOVING

THE BLADE (FIGURES 2, 3, 4, AND 5)

6. Press the spindle lock button again, tighten the hex-

head bolt by turning the spanner clockwise while

pressing the spindle lock button. (Fig. 5)

7. After tightening the hex-head bolt, release the spindle

lock button.

REMOVING THE BLADE

1. Pressing the spindle lock button, turn the hex-head

bolt with the spanner until the spindle locks.

2. Loosen the hex-head bolt by turning the spanner

anticlockwise while pressing the spindle lock button.

3. Remove the hex-head bolt and the outer blade

washer.

4. Retract the lower guard back as far as possible under

the upper guard, then remove the saw blade.

ADJUSTING THE RIVING KNIFE

(FIG. 6)

WARNING!

Do not use saw blades the disk of which is

thicker, or the set of which is smaller, then the

thickness of the riving knife.

1. Ensure that the riving knife is adjusted so that (Fig. 6):

A. The distance between the riving knife (11) and the

toothed rim of the saw blade is under 5 mm.

B. The toothed rim does not extend more than 5 mm

beyond the lower edge of the riving knife.

2. The riving knife should always be used except when

making a plunging cut in the middle of a workpiece.

ADJUSTING THE DEPTH OF CUT (FIG. 7A, 7B,

8, 9)

1. To adjust the depth of cut, loosen the depth

adjustment knob (12). (Fig. 7A)

2. Slide the base plate (13) to the desired depth using

the depth adjustment lug (21) and retighten the knob

securely. (Fig. 7B)

3. The depth of cut (14) can be determined by the depth

scale (15) or by measuring the distance by which the

blade protrudes from the base plate. (Fig. 8 and 9)

ADJUSTING THE CUTTING ANGLE (FIG. 10A,

10B)

1. The cutting angle may be set to any position between

0° and 45°. (Fig. 10A)

2. Loosen the bevel adjustment knob (16) at the front

of the tool and move the base plate to the desired

angle using the bevel scale (17). (Fig.10B)

3. Once the angle has been set, be sure to retighten

the bevel adjustment knob firmly.

TRIGGER SWITCH (FIG. 11)

This tool is started and stopped by squeezing and

releasing the trigger switch (18). To prevent the tool

from being started accidentally, the trigger can only

be operated if the safety button (19) is depressed first.

The safety button can be depressed with the thumb

leaving the other fingers free to squeeze the trigger

switch. It is not necessary to maintain pressure

on the safety button once the trigger switch has been

depressed.

OPERATING INSTRUCTIONS (FIG. 12)

DANGER!

KEEP HANDS AWAY FROM THE CUTTING

AREA WHEN OPERATING THE TOOL.

KEEP THE CORD AWAY FROM THE CUTTING

AREA AND POSITION IT SO THAT IT WILL

NOT GET CAUGHT ON THE WORKPIECE

DURING THE CUTTING OPERATION.

When cutting, use steady and even pressure

(DO NOT FORCE) in order to obtain a uniform cut.

Cut at a speed suited to the workpiece. (Cut slowly

if the workpiece is hard.) Inspect the saw blade

frequently and replace or sharpen it if dull, to avoid

overloading the motor.

CUTTING POSITION (FIG. 13A, 13B)

When cutting a workpiece at 0°, use point "A" of the

base plate line guide (20) and move the saw along

the pencilled line you have drawn. When cutting at

45°, use point "B". This line guide shows an

approximate line of cut. Make a sample cut in scrap

lumber to determine the actual line of cut.

CAUTION!

When ripping, the rip fence should only touch

the workpiece slightly. Do not force.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

EWS-1266EWS-1366(EU).qxd 11/24/2004 4:49 PM Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi EWS-1366 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info