Bedienungsanleitung Samson C.control (Seite 11 von 76) (Deutsch, Englisch, Französisch, Spanisch)

629996

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Setting-up the C•control

C control 2-Track Line Outputs

The C control features three 2-track /Stereo outputs allowing you to connect the inputs of a variety of record-

ing devices such as DAT recorders, Open Reel Half-tracks, Cassette recorders or CD players/burners. The signal

that is assigned in the C controls Source section is always present at all the 2-track outputs, and is always at

full strength and not affected by the Control Room level knob. To avoid feedback loop problems, be sure to

match the 2-track outputs with the associated 2-track inputs. In other words, if you connect your DAT recorder

to the 2-track A inputs, be sure to connect 2-track A outputs to the DAT recorder’s inputs. C control provides

many inputs and outputs for connecting your gear, so there are many ways the unit can be interfaced. The

following section describes the 2-Track outputs and how they can be used with equipment commonly found

in a recording studio. There is also a “Typical Set-up” diagram on page 15 of this manual and a wiring guide on

page 17 to help you choose the correct cables for your set-up.

2-track A Outputs

The 2-Track A outputs are balanced, 1/4-inch, TRS (Tip/ Ring/ Sleeve) phone connectors which output a +4dB

line level signal. You can interface a professional DAT machine, Open Reel Half-track or CD burner here.

2-track B Outputs

The outputs labeled 2-Track B are balanced, 1/4 inch, TRS(Tip/Ring/Sleeve) connec-

tors which output +4dB line level signal. You can use these outputs to connect the

inputs of a consumer cassette or CD recorder here.

2-track C Outputs

The 2-Track C inputs are unbalanced, RCA connectors which accept -10dB line level

sources. You can use these outputs to connect the inputs of a consumer cassette or

CD recorder here.

Connecting Line Level Speaker Outputs

The C control provides three sets of line level outputs for connecting up to three pairs of studio monitors. The

Speakers outputs are selected from the front panel speaker selection switches. Speaker Outputs A and B are

switched and are typically used to switch between a pair of near-field and far or mid-field monitors. Speaker

Output C/Sub can be independently turned on or off, so it is ideal for connecting a sub woofer that you may

want to turn on for a big “hyped club” sound, but turn off for critical mixing. There is more information on

the speaker switching feature in the section “Operating C control” following later in this manual. There is also

a “Typical Set-up” diagram on page 15 of this manual and a wiring guide on page 17 to help you choose the

correct cables for your set-up.

POWER

AC IN

14 V

SAMSON

MADE IN CHINA

500mA

MIX IN

2TK

A2TK B2TK C2TK A2TK B2TK C

SPK AEXT CUE

TALK

REMOTE

SPK B

SPK

BALANCEDBALANCED

BALANCEDBALANCED BALANCED

INPUT

OUTPUT

SPK

BALANCE

567

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson C.control Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info