629996
12
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
ENGLISH
Setting-up the C•control
10
Speaker A
The Speaker A outputs are balanced, 1/4-inch, TRS (Tip/ Ring/ Sleeve) phone connectors which output a +4dB
line level signal. You can connect to an active studio monitor or power amplifier here.
IMPORTANT NOTE:
In order to maintain the best gain structure and signal to noise ratio, we highly recom-
mend that only balanced cables be used on the SPEAKER A outputs. For detailed balanced cable wiring dia-
grams, please see page 17 in this manual.
Speaker B
The Speaker B outputs are unbalanced, RCA connectors which output -10dB line level signal. You can connect
to an active studio monitor, multimedia speaker or power amplifier here.
Speaker C
The Speaker C outputs are unbalanced, RCA connectors,
which output -10dB line level signal. You can connect to
an active studio monitor, multimedia speaker or power
amplifier here.
External Cue Output
The External Cue outputs are balanced, 1/4-inch, TRS
(Tip/ Ring/ Sleeve) phone connectors which output a
+4dB line level signal. This output is used to connect the
signal from the Talkback microphone to your headphone
cue mix. Many good headphone amplifiers such as the Samson C cue 8 or Samson S phone provide an auxilia-
ry input so that you can mix in the signal from the talkback mic with the stereo cue mix from your mixing con-
sole. This convenient feature allows the engineer and/or producer to talk to the talent over the headphone
mix. There is more information on the Talkback feature in the section “Operating C control” following later in
this manual.
TALK REMOTE
The C control’s TALKBACK microphone can be turned on and off from an external switch connected to the
TALK REMOTE input. The 1/4-inch phone jack is wired, “normally-open, so a switch that shorts the TALK
REMOTE jacks TIP to its SLEEVE will turn the TALKBACK microphone on and off in a momentary action. This
will allow the producer to move freely about the studio while talking to the talent.
AC INLET
The AC Inlet is where the C control receives it power from the included 18-volt AC power supply. Be sure to
use only the Samson AC1800 when operating the C control.
.
POWER
AC IN
14 V
SAMSON
MADE IN CHINA
+
-
500mA
MIX IN
2TK
A2TK B2TK C2TK A2TK B2TK C
L
R
L
R
R
L
SPK AEXT CUE
TALK
REMOTE
SPK B
SPK
C
BALANCEDBALANCED
BALANCEDBALANCED
BALANCEDBALANCED BALANCED
INPUT
OUTPUT
8
9
10
11
12
13
891011
13
12
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Samson C.control wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info