Bedienungsanleitung Samson D-2500 (Seite 16 von 32) (Englisch)

629999

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Once the highs return, the Enhance releases automatically.

Of course the D2500 let’s you dial up just the right amount

of Enhancer for your project, so follow the steps below to

activate the Enhancer.

• Press the ENHANCER switch so that the yellow LED is lit.

• Engage the effect by pressing the IN / OUT switch until

the yellow LED lights.

• Now, use the Data Wheel to select the correct Enhancer

setting , from 0 to 100%, that’s right for your application.

Setting up and Using the High Pass and Low Pass Filters

The D2500 includes digital High-pass and Low-pass fil-

ters for creating quick equalization curve contours. A

Hi-pass filter, (sometimes called a low-cut filter), is used

to attenuate the frequencies below a certain point. The

HP filter passes the highs, but cuts the lows. A Low-pass

filter, (sometimes referred to as a high-cut filter), is used

to attenuate the frequencies above a certain frequency

point. The LP filter passes the lows, but cuts the highs.

You can use the High and Low pass filters for a variety of

applications. Using the High-pass filter can be especially

useful in removing the low frequencies that can some-

times cause stage rumble. If you have a lot of high fre-

quency system noise and hiss, you can use the Low-pass

filter to roll-off the high-end of your system. When equal-

izing a monitor system, you may use both the HP and LP

filters to roll-off the high and lows for a vocal eq contour.









Any good high and low-pass filter will allow you to choose

the cut-off frequency, and also, the order, or slope, at

which the filter will attenuate. The D2500 lets you set the

frequency at which the HP or LP filters cut from, as well as,

a slope of either 6, 12 or 18 db per octave.

The HP / LP Switch Has Four Clicks!

Click Menu Function Value

1 Highpass low Cut Filter

20 Hz - 200 Hz

2 HP-Order Filter Slope 0, 6, 12, 18 per Octave

3 Lowpass low Cut Filter

2 kHz - 20 kHz

4 Lp-Order Filter Slope 0, 6, 12, 18 per Octave

• Press the HP / LP switch so that the yellow LED is lit.

• Engage the effect by pressing the IN / OUT switch until

the yellow LED lights.

• To set the High-pass filter press the HP / LP switch until

the LCD display reads; High-pass.

• Now, use the Data Wheel to set the frequency from 20

Hz to 200 Hz.

• Press the HP / LP switch again and you will see the menu

to set filter Order, or slope. The menu will read HP-

Order.

• Use the Data Wheel to choose a slope of either 6dB,

12dB, or 18 dB.

• To set the Low-pass filter, press the HP / LP switch until

the LCD display reads; Low-pass.

• Now, use the Data Wheel to set the frequency from 20

kHz to 2 kHz.

• Press the HP / LP switch again and you will see the menu

to set filter Order, or slope. The menu will read LP-Order.

• Use the Data Wheel to choose a slope of either 6dB,

12dB, or 18 dB.















Operating the D2500

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson D-2500 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info