Bedienungsanleitung Samson MDR1688 (Seite 13 von 28) (Englisch)

23501

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

in any optional headphones plugged in to the PHONES

connector located in the front panel jack field. If the

AFL/PFL MODE switch, located in the master section, is

switched out, the signal is sent pre fader, so you can hear

the signal regardless of the position of the channel vol-

ume Fader. This allows you to listen to a channel by itself:

(let's say) to see if an artist is out of tune, or to cue up a

channel without having to play it through the main PA

speakers. If the AFL/PFL MODE switch is switched in, the

signal is sent post fader, the signal you hear is dependant

on the position of the channel volume Fader. This allows

you to hear if there is any distortion on a channel added

by the level of the channel fader.

11- SOLO LED

The MDR1248 and MDR1688’s Mono Input channels

include a SOLO LED which, when illuminated, indicates

that the signal is assigned to the SOLO bus.

12 - PEAK LED

The MDR1248 and MDR1688’s MIC/LINE pre-amp also

includes a PEAK LED which, when illuminated, indicates

that the signal is peaking or overloading. To reduce dis-

tortion, lower the GAIN control to keep this LED from stay-

ing on.

13 - CHANNEL LEVEL

The MDR1248 and MDR1688’s LEVEL control knobs are

used to adjust the overall channel volume.

STEREO INPUT CHANNEL SECTION

The MDR1248 and MDR1688 feature stereo input chan-

nels for connected stereo line level devices like keyboards

and drum machines, as well as the outputs from effects

processors and digital guitar modelers. The MDR1248 has

four sets of stereo inputs which make up channels 5/6,

7/8, 9/10 and 11/12, while the MDR1688 has four sets of

stereo inputs which make up channels 9/10, 11/12, 13/14

and 15/16. The Stereo input channels have a four-band

fixed equalizer and AUX 1 and 2 sends and are laid out the

same as the mono inputs. The following section details

the stereo input controls:

14- GAIN switch

The MDR1248 and MDR1688’s pre-amp stage has a vari-

able GAIN switch with a range of -10 to +4dB on the ste-

reo LINE input.

15 - LOW/LOW MID/HIGH MID/HIGH - Channel

Equalizer

The MDR1248 and MDR1688 Stereo input channels fea-

ture a 4-band equalizer allowing you to adjust the high,

mid, and low frequencies independently on each channel.

The stereo channel equalizer is laid out like a mono input

on the control panel input strip, but internally, the equal-

izer is effecting a stereo signal path. The channel’s fre-

quency response is flat when the knobs are in the “12:00”

position. Rotating the knob towards the right will boost

the corresponding frequency band by 15dB, and rotating

























Controls and Functions

it towards the left will cut the frequency by 15dB. The fre-

quency centers, range of boost or cut, and equalizer type

for each band are as follows:

High: 12kHz +/- 15dB shelving type

High Mid: 3kHz +/- 15dB peaking type

Low Mid: 500Hz +/- 15dB peaking type

Low: 80Hz +/- 15dB shelving type

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR1688 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson MDR1688

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info