Bedienungsanleitung Samson MDR1688 (Seite 15 von 28) (Englisch)

23501

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

MASTER SECTION

26 - 2 TRK LEVEL

The 2TK LEVEL control knob is used to set the volume

level of the source connected to the 2-track input. If you

want to mix in a CD, tape or MP3 player with your input

channels connected to the 2TK inputs, use the 2TK LEVEL

to adjust the level.

Auxiliary Returns

The MDR1248 and MDR1688 have two stereo auxiliary

returns, which can be accessed via the two pairs of 1/4-

inch phone jacks located on the master section jack field.

The auxiliary returns can be used to connect any stereo

line level signal, but they are primarily used to connect

the output of external effects processors.

Controls and Functions

27 - AUX RET 1 control knob

This adjusts the amount of signal that is sent from the AUX

1 RET jacks to the MAIN bus.

28 - AUX RET 2 control knob

The AUX RETURN 2 adjusts the level of the signal present

at the AUX 2 RET jacks. This signal is summed, or mixed in

to the main L/R MIX bus.

29 - AUX 2 RETURN TO AUX 1 switch

This routes the signal that is present on the AUX 2 RETURN

jacks to AUX 1 so that the effects can be heard in the

monitor mix.

30 - AUX 1 SEND control knob

The master AUX SEND control is used to send the effect

mix bus to an external effect device connected to the AUX

SEND 2 jack.

31 - AUX 2 SEND control knob

The master EFX SEND control is used to send the effect

mix bus to an external effect device connected to the AUX

SEND 2 jack.

32 - ALT 3/4 Level control knob

Use this control knob to set the level of the mix created

from the channels assigned to the 3/4 bus. The ALT 3/4

level control will control the level of the signal being

sent to the 3/4 Output jacks. When the Master ALT 3/4

switch(43) is switched in, the ALT 3/4 level control will con-

trol the level of the ALT 3/4 mix that is heard in the Main

Left and Right mix. Remember, the ALT 3/4 TO MIX switch

must be set to the on or down position in order to hear

the 3/4 mix in the main Left and Right mix.

33 - SOLO LED

The LED will illuminate when any one or more channel's

SOLO switch is engaged, indicating that there is a channel

in solo.

34 - LEVEL SET LED

When a channel's SOLO switch is pressed, the LEVEL SET

LED will illuminate and flash indicting that the channels

input level is now being measured by the main VU meter.

35 - MODE (AFL/PFL) switch

You can change the mode of the SOLO bus from Pre fader

listen to After, or Post fader listen using the MODE switch.

When the switch is pressed in, the SOLO mode is set to

AFL (After Fader Listen), so the channels signal is sent after

or post fader. When the switch is pressed out, the SOLO

mode is set to PFL (Pre Fader Listen), so the channels sig-

nal is sent before or pre fader.

36 - PROGRAM control knob

The MDR1248 and MDR1688 feature an internal 24-bit

DSP with 256 presets. The presets are organized in sixteen

Program banks, each with sixteen variations. The Program

control knob used to select one of the sixteen DSP effect

programs.

37 - VARIATION control knob

The MDR1248 and MDR1688 feature an internal 24-bit





















 

















 





Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR1688 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson MDR1688

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info