Bedienungsanleitung Samson MDR1688 (Seite 17 von 28) (Englisch)

23501

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

equalizer, compressor, noise gate, reverb and other audio

devices. For more information on the channel INSERT

points, see the section, “Using the Channel Insert Jacks” on

page 17 of this manual.

Stereo Input Channels - Line Inputs

You can connect the outputs from stereo devices such as

synthesizers, drum machines, effects processors or any

stereo line-level signal. The LINE inputs have a nominal

operating level of -40dBV through - 10dBV. The 1/4-inch

TRS phone jacks Connector pin-out are as follows; Sleeve:

Ground, Tip: Hot (+), Ring: Cold (-)

D- LEFT MONO

The LEFT MONO jack is used to connect the left output of

a stereo device to the Left input of the MDR’s stereo input

channels or use the LEFT input when connecting a mono

input signal to the Stereo Input channels.

E - RIGHT

The RIGHT jack is used to connect the Right output of a

stereo device to the Right input of the MDR’s stereo input

channels.

MASTER SECTION INPUT AND OUTPUT JACKS

The MDR1248 and MDR1688 features several input and

output connectors allowing you to interface a variety of

external devices. A stereo recording device, such as a cas-

sette recorder, can be connected to the 2 Track jacks, and

power amplifiers or powered monitors can be connected

to the CONTROL ROOM and MAIN output jacks.

F - ALT 3/4 LEFT/RIGHT OUTPUT

The ALT 3/4 outputs are 1/4-inch balanced jacks carrying the

signal from the 3/4 bus. You can assign a channel or a group

of channels to the 3/4 bus using the MUTE 3/4 switch on the

stereo and mono input channels. The 3/4 output connectors

are labeled Left and Right since the 3/4 bus follows the chan-

nels’ PAN control allowing it to be used for a second stereo

MONO INPUT CHANNELS - MIC and LINE INPUTS

Channels 1 through 4 on the MDR1248 and channels 1

through 8 on the MDR1688 are mono inputs, each pro-

viding a 1/4-inch connector for line level signals and an

XLR connector for the MIC signals. Channels 5/6 through

11/12 on the MDR1248 and channels 9/10 through 15/16

on the MDR1688 are stereo inputs, providing a pair of 1/4-

inch connectors for line level inputs. By using the GAIN

control on the mono channels, you can connect a variety

of signal sources from microphones to line level devices

such as synthesizers, and drum machines. All the LINE

and MIC inputs are balanced. The MIC inputs are compat-

ible with microphones with output impedances of 50-

600 Ohms and the LINE inputs are compatible with line

level devices of 600 Ohms. Following below is a detailed

description of the MDR1248 and MDR1688’s input and

output connectors.

NOTE: It is not possible to simultaneously use both the

LINE and MIC inputs on the same channel. Use only one of

the inputs for the appropriate source on each channel.

A - Microphone Input - Mono Input Channels

Use these inputs to connect Low Impedance micro-

phones and low level signals from direct boxes. The MIC

inputs have a nominal operating level of –50dBu through

-20dBu. The MIC inputs also feature +48V phantom

power, allowing you to use condenser microphones. The

Phantom Power switch (located on the MDR1248 and

MDR1688’s rear panel) enables phantom power on all

the microphone inputs when set to the ON position. XLR

Connector pin-out - Pin 1: Ground, Pin 2: Hot (+), Pin 3:

Cold (-)

B - Line Level Input - Mono Input Channels

Use these inputs to connect synthesizers, drum machines,

effects processors or any line-level signal. The LINE

inputs have a nominal operating level of -40dBV through

- 10dBV. TRS phone jacks Connector pin-out - Sleeve:

Ground, Tip: Hot (+), Ring: Cold (-)

C - Insert Point Jack - Mono Input Channels

The MDR1248 and MDR1688’s mono input channels fea-

ture a 1/4-inch, TRS INSERT jack providing a patch point to

connect an external processor. You can use these connec-

tions to interface an external signal processor like an

MDR1248 and MDR1688 Input and Output Connections

(

)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR1688 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samson MDR1688

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info