Bedienungsanleitung Samson SERVO 600 (Seite 6 von 16) (Englisch)

629803

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Guided Tour - Front Panel

1: Fan Vent

- The Servo Series amplifiers stay cool thanks to their twin, forced-air cooling tunnels. Cool air is drawn through

the front panel fan vents, reducing the temperature of the internal components while forcing the heat out the rear vents.

The fans will actually sense the internal temperature and adjust their speed to maintain the optimum cooling conditions.

2: Channel input level controls

- These 42-position detented controls allow you to precisely adjust the input level of the

signal arriving at the rear-panel input jacks (see #1 and #5 on the following page). At their fully counterclockwise posi-

tion (labeled “MIN”), the signal is attenuated by 80 dB (essentially completely off). At their fully clockwise position (labeled

“MAX”), the signal is at unity gain (that is, no attenuation). When +4 dBu of signal arrives at the input jacks and the Channel

input level controls are set to their fully clockwise position, the Servo Series delivers full power output.

3: LED meters

- These ten-segment LED meters continuously monitor the power output level for the corresponding chan-

nel. For convenience, the segments are labeled, from left to right, -24 dB, -20 dB, -16 dB, -12 dB, -8 dB, -4 dB, -2 dB. O, +2 dB

and +4 dB (PEAK). The right (PEAK) segment lights whenever the channel is outputting signal at full strength. For the best

signal-to-noise ratio, the right (PEAK) segment should light occasionally during peak levels; if it lights frequently, you may

be overloading the amplifier and a distorted (“clipped”) signal is probably being output. If this occurs and backing off the

Input Level control delivers too low an output level for your application, consider using Bridged mode (see the “Bridged

Mode” section on page 8 in this manual for more information).

4: Power switch

- Use this to power the Servo Series on or off. The internal LED lights whenever the Servo Series is powered

on.

5: Signal LED

- The front panel LED indicators continuously monitor the power output level for the corresponding channel.

The SIGNAL LED lights whenever output signal is present.

6: Protection LED

- This goes on for approximately five seconds whenever the Servo Series is powered on and then turns

off (you’ll hear a “click” when it does so). The Protection LED will also light when overheating or other severe problems occur

(see page 6 in this manual for more information). It is normal for the Protection LED to fade slowly when the amp is pow-

ered off. When lit, no signal is provided to any connected speakers, thus muting them and preventing any “thump” from

occurring. For a complete description of the conditions under which this light goes on, see the section entitled “The Servo

Series Protection Circuitry” on page 7 of this manual.

7: Peak LED

- The PEAK segment lights whenever the channel is outputting signal at full strength. For the best signal-

to-noise ratio, the right (PEAK) segment should light occasionally during peak levels; if it lights frequently, you may be

overloading the Servo Series and a distorted (“clipped”) signal is probably being output. If this occurs and backing off the

Input Level control delivers too low an output level for your application, consider using Bridged mode (see the “Bridged and

Parallel Modes” section on page 8 in this manual for more information).











 





 





 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson SERVO 600 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info