Bedienungsanleitung Samson SERVO 600 (Seite 7 von 16) (Englisch)

629803

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Guided Tour - Rear Panel

1: RCA Input connectors

– You can connect unbalanced incoming signals to the Servo series using the RCA connectors, which

are wired as follows: Pin 2 (or Tip) hot, and Pin 1 (or Sleeve) ground. The Servo Series accepts input levels of any strength but

needs at least -10dBV dBu to achieve maximum power. Stereo signals should be connected to both the Channel 1 and Channel

2 input jacks; however, when operating the Servo Series in Bridged mode, use the Channel 1 input jack only. See page 8 in this

manual for more information about Bridge mode and page 9 in this manual for full interconnection instructions.

2: Fan

- This variable-speed fan provides vital cooling to your Servo Series (the hotter the amp gets, the faster the fan blows!).

Make sure that both the front and rear panels are kept free of all obstructions and that cool, fresh air is accessible at all times.

Also, try to ensure that the Servo Series is used in a dust-free environment.

3: 1/4-inch Output Connectors

- Use these to connect each channel of the Servo Series to, 4-ohm or 8-ohm loudspeakers with

1/4-inch input jacks. See page 8 in this manual for more information about Bridged mode and page 9 in this manual for full

speaker connection instructions.

4: 5-way Binding Post

- Use these to connect each channel of the Servo Series to 4-ohm or 8-ohm loudspeakers. Be sure to con-

nect the loudspeaker correctly, with the red (+) terminal normally connected to the positive input of the speaker and the black

(ground) terminal normally connected to the negative input of the speaker. See page 8 in this manual for more information

about Bridge mode and page 9 in this manual for full speaker connection instructions

5: 1/4-inch Input Connectors

- Connect incoming signals to these electronically balanced inputs, using the 1/4” TRS (Tip/Ring/

Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot, Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use of bal-

anced three-conductor cabling wherever possible (unbalanced two-conductor 1/4” plugs can also be inserted into these inputs,

but you’ll get better signal quality and less outside noise and hum if you use balanced lines). The Servo Series accepts input levels

of any strength but needs at least +4 dBu to achieve maximum power. Stereo signals should be connected to both the Channel

1 and Channel 2 input jacks; however, when operating the Servo Series in Bridged mode, use the Channel 1 input jack only. See

page 8 in this manual for more information about Bridge mode and page 9 in this manual for full interconnection instructions.

6: AC input

- Connect the supplied heavy-gauge 3-pin “IEC” power cable here.

7: Bridge / Stereo switch

- For normal operation, place this two-way switch in its lower (“STEREO”) position. When placed in its

upper (“BRIDGE”) position, the signal arriving at the Channel 1 input only is again routed to both power amplifiers (again, the

Channel 2 input is ignored), but the two power amplifiers are bridged together. For more information, see the “Bridge Mode”

section on page 8 in this manual and the “Servo Series Connections” section on page 9 in this manual. WARNING: Due to the

extremely high power output of the Servo Series when used in Bridge mode, be sure to use only loudspeakers sufficiently rated to

handle the resultant wattage (in Bridge mode, these must be 8-ohm speakers).

     

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson SERVO 600 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info