Bedienungsanleitung Samsung DSBA200C (Seite 32 von 41) (Englisch, Italienisch)

29539

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

GB-17

DSB-A200C

GB-16

DIGITAL SATELLITE RECEIVER

DSB-A200C

1.1 LNB Setting

You can select the satellite and LNB setting conditions

to execute channel search and you can alter the settings

for 22KHz tone. The parameters set in this menu are

needed for programming the channels for the “Auto scanning”

and “Manual scanning”.

The necessary information can be found at your

antenna and LNB brochures, or you can ask your dealer.

● Select LNB power supply “On”.

● Select the desired satellite name.

● Select the LNB type (frequency).

● Select the DiSEqC Mode

(Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B)

If you are using a Positioner, select Positioner DiSEqC1.2 (“Yes” or “No”)

22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone

switch box, with the 22 KHz tone switch (“On”, “Off” or “Auto”) you can switch

between both LNB or antennas.

0/12V: When you use two LNBs or antennas is switched to 0/12V, select what LNB and

antenna are used enable or disable. 0/12V terminal is located on the rear of STB.

1.2 Positioner Setting

If you have a DiSEqC 1.2 motorized system

which is fully compatible with DiSEqC1.2, then you can

take advantage of the DiSEqC 1.2 functions available.

● Select Satellite.

● Select any transponder from above satellites and

check out the Frequency, Symbol Rate, FEC and Polarity.

In case problems arise, ask your dealer.

Sometimes this transponder may not exist due to broadcasting.

It is better to select main transponder among them for the

desired satellite.

● Select from Menu Mode:

“User” mode : Enables control of basic positioner function

recommended for beginners. General user uses “User” mode.

“Installer” mode : This is used to search for the position of a satellite manually.

OPERATING THE RECEIVER

Main Menu

After installing your antenna system and STB with appropriate connectors.

● Plug in the AC main power and switch on the receiver.

● Press MENU key to bring up the main menu.

The LED display will show

“

”

The following on screen display will appear:

The sub menu topics will be displayed.

For the sub-menus Installation, Channel Organising and

Parental Lock you need the PIN Code.

Before you begin with the “Installation” menu,

you should check in the 4th menu “System Setup”

whether all the information there is applicable for you.

● To see the help message, press the YELLOW(ALT) key.

1. Installation

The menu provides settings for customizing, adding new

services and displaying the status of the receiver.

● Select “Installation” in the main menu mode to select the

sub menu.

● Enter the PIN Code.

If you have not entered your own PIN Code then the

PIN Code 0000 applies, which was set at the factory.

DSB-A200C_GB 10/24/03 10:27 AM Page 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung DSBA200C Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info