Bedienungsanleitung Samsung NZ85C5047 (Seite 8 von 34) (Englisch)

805042

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

8 English

Installing the hob

Tools you will need

Pencil Phillips Head Screwdriver Ruler or Straightedge

Safety Glasses Saber Saw Drill

Connecting to the mains power supply

Before connecting, check that the nominal voltage of the appliance, that is, the

voltage stated on the rating plate, corresponds to the available supply voltage. The

rating plate is located on the lower casing of the hob.

WARNING

It should be installed suitably by a component or trained person.

Shut off power to circuit before connecting wires to circuit.

The heating element voltage is AC 230 V~. The appliance also works perfectly on

networks with AC 220 V~ or AC 240 V~. The hob is to be connected to the mains

using a device that allows the appliance to be disconnected from the mains at all

poles with a contact opening width of at least 3 mm, eg. automatic line protecting

cut - out, earth leakage trips or fuse.

WARNING

The cable connections must be made in accordance with regulations and the

terminal screws tightened securely.

WARNING

Once the hob is connected to the mains supply, check that all cooking zones are

ready for use by briey switching each on in turn at the maximum setting with

suitable cookware.

Installing the hob

WARNING

Be sure the new appliance is installed and grounded only by qualied personnel.

Please observe this instruction. The warranty will not cover any damage that may

occur as a result of improper installation.

Technical data is provided at the end of this manual.

Safety instructions for the installer

• A device must be provided in the electrical installation that allows the

appliance to be disconnected from the mains at all poles with a contact

opening width of at least 3 mm. Suitable isolation devices include line

protecting cut - outs, fuses (screw type fuses are to be removed from the

holder), earth leakage trips and contactors.

• With respect to re protection, this appliance corresponds to EN 60335 - 2 -

6. This type of appliance may be installed with a high cupboard or wall on one

side.

• The installation must guarantee shock protection.

• The kitchen unit in which the appliance is tted must satisfy the stability

requirements of DIN 68930.

• For protection against moisture, all cut surfaces are to be sealed with a

suitable sealant.

• On tiled work surfaces, the joints in the area where the hob sits must be

completely lled with grout.

• On natural, articial stone, or ceramic tops, the snap action springs must be

bonded in place with a suitable articial resin or mixed adhesive.

• Ensure that the seal is correctly seated against the work surface without any

gaps. Additional silicon sealant must not be applied; this would make removal

more difcult when servicing.

• The hob must be pressed out from below when removed.

• A board can be installed underneath the hob.

• The ventilation gap between the worktop and front of the unit underneath it

must not be covered.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung NZ85C5047 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Samsung NZ85C5047

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info