Bedienungsanleitung Sangean ATS-909X2 (Seite 16 von 19) (Englisch)

797034

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

The TIMER indicator (J), the corresponding Timer

number indicator (M) and the Alarm source indicator (K

/ L) of the selected alarm source will now blink on the

display.

2. Select the alarm source (radio or buzzer) using the

SSB button (6).

The indicator of the selected alarm source (K / L) will

be blinking on the display.

3. Use the numeric buttons (19) to set the alarm time (e.g.

to enter 11:00, press 1-1-0-0).

4. Press the Enter button (30) to confirm the alarm time

and the alarm source.

5. The radio will produce a beep to indicate that the

settings have been saved and the alarm is activated.

6. If the radio is set to use the 12-hour clock format, press

the Decimal point button (32) to set either AM or PM.

When PM is selected, the PM indicator (E) will be

shown on the display.

If the alarm source has been set to radio in step 2, a

radio station should still be added to the alarm. To do

this:

7. Tune to a radio station as previously described.

8. Press the Memo button (24).

The Memo indicator (X) and preset indicator (S) will

now be blinking on the display.

9. Press the timer button (5) of the alarm timer that you

want to assign the station to.

When an alarm timer has been set and is active,

the corresponding Timer number indicator (M) will

permanently be shown on the radio's display. The

alarm timer that is closest to the current time is marked

with a rectangle in the Timer number Indicator (M).

NOTE

The buzzer alarm uses the Humane Wake System

(HWS). This means that when the buzzer alarm

activates, the alarm will start softly and gradually

increase in volume. It will repeatedly sound for 1 minute

and be muted for 1 minute over a period of 30 minutes,

unless the alarm is stopped. If a radio station is used

as the alarm source, then the radio will sound non-stop

at the selected time for 60 minutes, unless the alarm is

stopped.

WHEN AN ALARM SOUNDS

STOPPING AN ALARM

When an alarm sounds, press the POWER button (10) to

stop the sounding alarm.

USING THE SNOOZE FEATURE

When an alarm sounds, press any button (except the

Power button (10) or Backlight button (11)) to snooze

the alarm for 5 minutes. This procedure can be repeated

during the alarm period. The Snooze indicator (H) is

shown on the display while the snooze feature is active.

DEACTIVATING AN ALARM TIMER

If an alarm timer is activated, press the corresponding

timer button (5) followed by the Cancel button (31) to

deactivate the alarm timer. The corresponding Timer

number indicator (M) will now no longer be shown on the

display.

SETTING THE SLEEP TIMER

The sleep timer allows you to automatically turn off the

radio after a preset time has elapsed. It can be set from

90 minutes to 10 minutes in 10 minute decrements.

To set the sleep timer, press and hold the Power button

(10) and release it when the desired sleep time is shown

in the Text display (U) on the display. An active sleep timer

is indicated on the display by the Sleep timer indicator (I).

DISPLAYING SIGNAL INFORMATION

The Info button (29) can be used in all modes to display

basic information about the signal that is being received.

After tuning to a radio station on the SW, MW, LW or AIR

band, or an FM station that is not broadcasting RDS /

RBDS information, repeatedly press the Info button (29)

to display the following information in sequence:

1. Preset or page name - Display the name of the preset

or preset page.

2. Signal RF strength - Displays the signal strength in

dB.

3. Signal to Noise ratio - Displays the signal to noise

ratio in dB.

4. Memory bank A / B / C - Displays the memory bank

that is currently being used.

The available layers of information and the information

that is displayed are also shown in the table below:

Layer SW / MW / LW / AIR / FM without

RDS or RBDS

1 Preset or page name

2 RSSI -- xxDB

3 SNR -- xxDB

4 MEMOBANK - A / B / C

Note: RSSI: Radio Signal Strength Indication

SNR: Signal to Noise Ratio

NOTE

If your radio is tuned to an FM station that broadcasts

RDS / RBDS information, the Info button (29) can show

additional information. Refer to the next section for more

information about RDS and additional information it

offers.

USING THE RDS FEATURE – FM ONLY

Radio Data System (RDS) is a service that allows FM

stations to broadcast additional information. The ATS-

909X2 is capable of receiving RDS / RBDS signals. When

receiving an FM radio station that broadcasts RDS data,

the station name will be displayed in the Text display (U)

and the display will show the RDS indicator (Aa).

If the RDS CT indicator (D) is shown on the display, this

means that the radio's clock has been automatically

synchronized with the clock signal broadcasted by the FM

radio station. This feature must be enabled (it is disabled

by default) for the radio to be able to synchronize its clock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean ATS-909X2 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean ATS-909X2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info