Bedienungsanleitung Sanibroyeur SANICOM 1 Expert-line (Seite 7 von 32) (Alle Sprachen)

532741

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ALARM

There is the option of connecting an alarm (light, bell) on to

the electronic circuit board (2 terminals fed with 220V). If the

motor is fed continuously (more than 5 minutes), the contact

will be made. This enables the user to carry out a check if he

wishes.

CONNECTION OF THE ALARM

Two 6.35 push on connection points are available on the

electronic circuit board (arrowed) for creating an alarm

circuit. (These connectors have a 220V, 0.5A maximum

current passing through them). To access them after turning

the power off, remove the cover then unscrew and unclip

the upper casing of the electronic box, to expose the

electronic circuit board. On this card use the point marked

E.V. and the unused neutral connection point marked N.

Use a round 2 x 0.75 mm2 wire, which must pass across

the lid of the upper casing, through the cable gland, before

being connected to the chosen alarm system.

USE

SANICOM

1 is designed for disposing of wastewater

originating from sinks, clothes washing machines,

dishwashers, showers or baths and basins.

SANICOM

1 can pump out hot water.

CAUTION:

1. Do not dispose of concentrated chemical products (acids,

solvents, bases, oxidants, reducers, etc.) into sanitary

ware connected to the SANICOM

2. In the event of power failure, stop all water flow to the

appliances connected to the SANICOM

WARRANTY

SANICOM

1 SFA is guaranteed for 2 years for labour and

parts, subject to correct installation and use of the

apparatus.

STANDARD

This piece of equipment complies with the EN 12050-2 stan-

dard (Lift station for effluents not containing faecal matter) and

the directives and European standards on electric safety and

electromagnetic compatibility.

ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A

PROFESSIONAL ELECTRICIAN

COMMISSIONING

Once the hydraulic and electrical connections have been

made, check that the connections are tight by allowing water

to flow through each entry point used. Ensure that the pump

is working properly.

FIRST LEVEL TROUBLESHOOTING

REMEDY

1. Check the electrical installation.

1. Vérifier l’arrivée d’eau, sinon

voir ci-dessous

PROBABLE CAUSE

1. The appliance is not switched on

2. The cable is defective

1. Pump blocked

2. Pump jammed

3. Too much water flowing

through

PROBLEMS

• Motor does not start

• The alarm sounds

For all other intervention, disconnect the electrical current.

PROBLEM ENCOUNTERED

• Motor does not start

• Pumps working constantly

• Alarm sounding

• Intermittent start-up of pumps

PROBABLE CAUSE

1. Pressure reader tube kinked or

out of position

2. Electronic card defective

1. Level pressure pipe is blocked

2. Vertical discharge too high

3. Electronic card defective

1. Pump blocked

2. Pump jammed

3 Electrical problems with motor

4. Too much water flowing

through

5. Electronic card defective

1. The non-return valve broken

or leaking

2. Electronic card defective

REMEDY

1. Remove or replace the tube.

2. Consult an SFA-approved

breakdown technician.

1. Extract the level pressure pipe

unblock it.

2. Examine the appliance.

3. Consult an SFA-approved

breakdown technician.

1. IAdjust the pump which is

displaying the alarm:

• Using a screwdriver, turn the

motor shaft by accessing it

through the hood.

• Remove the pump and

unblock it.

If the pump revolves but does not

pump, consult an SFA-approved

breakdown technician.

5. Consult an SFA-approved

breakdown technician.

1. Clean or change the valve.

2. Consult an SFA-approved

breakdown technician.

SECONDARY TROUBLESHOOTING

ELECTRICAL INSTALLATION MUST BE CARRIED

OUT BY A PROFESSIONAL ELECTRICIAN

REMOVAL

13a

REMOVING THE MOTOR

SWITCH THE APPLIANCE OFF (the yellow indicator light

must be out).

Empty the tank.

To access the anti-backflow valve:

Unscrew the clips and then remove the elbow (6).

Clean or replace the valve (8).

To remove the motor

Unscrew the six screws (66) torx T20.

Turn the motor anti-clockwise (warning: the motor may

be hot) and lift it out.

13b

REPLACING THE MOTOR

Locate the motor into the adaptor plate, ensure it is firmly

home and turn it clockwise until the reference marks line

up.

Screw in the six screws into the adaptor plate.

Check that the motor can turn freely using a screwdriver

into the top of the motor shaft.

ELECTRICAL INSTALLATION MUST BE CARRIED

OUT BY A PROFESSIONAL ELECTRICIAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanibroyeur SANICOM 1 Expert-line Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanibroyeur SANICOM 1 Expert-line

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info