Bedienungsanleitung Sanibroyeur SANICUBIC 1 WP - 168 (Seite 18 von 78) (Alle Sprachen)

671243

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

OPERATION OF THE ALARM

1/ General alarms:

Level alarm:

If the water level inside the device is abnormally

high: the buzzer is triggered + the red alarm LED

lights up + both motors start-up. If this LED ﬂashes

red, it indicates a detection problem for the normal

water level (Long dip tube).

Temporary alarm:

If one of the two motors runs for more than 1 mi-

nute: the buzzer is triggered + the red alarm LED

lights up + the other motor starts-up.

Mains alarm:

In case of power failure (or when unplugging the

device): the buzzer is triggered + the red alarm LED

lights up + the yellow mains LED ﬂashes.

2/ General alarm reset:

If the problem that triggered an alarm above di-

sappears, the buzzer stops, but the red alarm LED

remains lit as a reminder of the fact that the system

encountered a problem.

One of the two keypad keys will stop the buzzer

in all cases, but it will only turn oﬀ the red LED if

the problem that triggered the alarm has been

resolved. Alarms from the remote box also remain

active until the problem has been solved. This pre-

vents the system from being left unknowingly in a

faulty state

OPERATION OF THE ALARM UNIT

For wall mounting of the unit, use the following

image as a guide:

OPERATION OF THE SANICUBIC® 1/SANICUBIC®

1 WP/SANICUBIC® 2 Classic/SANICUBIC® 2 XL

WIRED ALARM UNIT

The SANICUBIC® alarm unit does not require a

separate power supply. The power is supplied

through the SANICUBIC®. In case of power failure,

the alarm unit’s battery takes over.

Connection of the alarm unit to the device:

Connect the alarm cable directly to the unit.

1/ The red general alarm LED reproduces the ope-

ration of the corresponding LED on the SANICUBIC®

control panel. The alarm unit sounds as long as the

fault is present. To stop the alarm, press the reset (*)

button on the device’s keypad or the button under

the alarm unit.

2/ The yellow «mains» LED indicates the power sup-

ply status of the alarm unit

-steadily glowing light = live SANICUBIC® connec-

ted to the mains supply

-ﬂashing = power failure on the SANICUBIC®.

OPERATION OF THE SANICUBIC® 2 PRO H/F

ALARM UNIT

The alarm unit is in HF connection -868 Mhz HF

with the SANICUBIC® 2 Pro. It receives various alarm

information from it. If other devices operating in HF

are disrupted by the system

(or vice versa), a commutation of the HF -868 Mhz

coding has been anticipated, which connects the

base card and the remote alarm unit.

In the event of interference with other HF devices

or other SANICUBIC® 2 Pro devices nearby, unplug

the unit and the remote module, switch one or

more of the 4 switches of the device’s card (SW2).

and do the same on the remote unit’s card.

Warning: the code must be the same for the 2

cards.

The alarm unit has 3 LEDs and 1 buzzer.

1/ The red «general alarm» LED reproduces the

operation of the corresponding LED on the SANI-

CUBIC® control panel.

2/ The yellow «HF reception» LED reproduces the

operation of the SANICUBIC® control panel’s yellow

mains LED:

INSPECTION AND MAINTENANCE

1/ Inspection

The proper running of the wastewater lifting sta-

tion should be checked by user once a month ob-

serving at least two starting cycles.

2/ Maintenance

The lifting station has to be regularly maintained

by a qualiﬁed person. Intervals should:

• Every 3 months for lifting stations installed in

commercial premises

• Every 6 months for lifting stations installed in col-

lective buildings

• Once a year for lifting stations installed in indivi-

dual houses

During maintenance, the following should be

done:

a) Check the watertightness of connections by

checking pipework to and from the lifting station

b) Activate the gate valves , check their smooth

function and their watertightness ( grease if neces-

sary)

c) Open and clean up the non return-valve system,

check it is functioning correctly

d) Clean up the pumping system and its connec-

tions, check the impeller and the cutting system

(for macerating pumps)

e) Clean up the inside of the collecting tank

f) Visually check the lifting station’s electrical

control box functions

Once the checks have been made, restart the lifting

station in compliance with the manual instructions

to check its proper running.

A report should be issued detailing the checks and

any notable points.

If non-compliances that cannot be solved have

been found, the qualiﬁed person in charge of the

maintenance work has to immediately inform the

lifting station’s user.

3/ Maintenance contract

It is advised to the users to establish a maintenance

contract for regular maintenance and checking.

- steady light = transmission OK, the SANICUBIC®

control panel connected to the mains supply

- blinking = transmission OK, but power failure on

the SANICUBIC® control panel (which then runs on

battery)

- oﬀ = no HF reception (check that the code is the

same as the SANICUBIC® control panel or loss of HF

signal (too far away) discharged or failure of the

SANICUBIC® control panel.

3/ Green «mains» LED indicates the power status of

the alarm remote unit:

- steady light = live unit connected to the mains

supply

- ﬂashing = mains failure on the unit (which is the-

refore operating on battery)

- oﬀ = failure of the unit or discharged battery

4/ The buzzer sounds continuously during an

alarm. It stops buzzing if the cause of the alarms

disappear or if you press the general alarm reset

button.

Reset (*) :

RED LED

général alarm

Yellow LED

Alarm

transmission

Green LED

mains alarm

Sanibroyeur SANICUBIC 1 WP - 168 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info