Bedienungsanleitung Sanyo PT-RS11K (Seite 158 von 219) (Englisch)

598873

158

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

Chapter 4 Settings — [NETWORK] menu

158 - ENGLISH

[DHCP]

[ON]

If a DHCP server exists in the network where the projector is to be

connected, obtains the IP address automatically.

[OFF]

If a DHCP server does not exist in the network where the projector

is to be connected, set [IP ADDRESS], [SUBNET MASK], and

[DEFAULT GATEWAY].

[IP ADDRESS] Enter the IP address when a DHCP server is not used.

[SUBNET MASK] Enter the subnet mask when a DHCP server is not used.

[DEFAULT GATEWAY] Enter the default gateway address when a DHCP server is not used.

4) Press as to select [STORE], and press the <ENTER> button.

5) When the confirmation screen is displayed, press qw to select [OK], and press the <ENTER> button.

Note

f When using a DHCP server, conrm that the DHCP server is running.

f Consult your network administrator regarding the IP address, subnet mask, and default gateway.

f When [Art-Net SETUP] is set to [ON(2.X.X.X)] or [ON(10.X.X.X)], [NETWORK SETUP] cannot be selected.

[NETWORK CONTROL]

Set up the control method of the network.

1) Press as to select [NETWORK CONTROL].

2) Press the <ENTER> button.

f The [NETWORK CONTROL] screen is displayed.

3) Press as to select an item, and press qw to change the setting.

[WEB CONTROL] Set to [ON] to control with the web browser.

[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.

[COMMAND CONTROL]

Set to [ON] to control with the <SERIAL IN>/<SERIAL OUT> terminal control command format

(x page 202). Refer to “Control commands via LAN” (x page 196).

[COMMAND PORT] Set the port number used for command control.

[Crestron Connected(TM)] Set to [ON] to control with Crestron Connected

of Crestron Electronics, Inc.

[AMX D.D.]

Set to [ON] to control with the controller of AMX Corporation.

Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, visit the

website of AMX Corporation.

URL http://www.amx.com/

[EXTRON XTP]

Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the <DIGITAL LINK/LAN>

terminal.

The [EXTRON XTP] setting must be set to [OFF] when connecting the optional DIGITAL LINK output

supported device (Model No.: ET-YFB100G, ET-YFB200G).

For details of the “XTP transmitter”, visit the website of Extron Electronics.

URL http://www.extron.com/

4) Press as to select [STORE], and press the <ENTER> button.

5) When the confirmation screen is displayed, press qw to select [OK], and press the <ENTER> button.

[NETWORK STATUS]

Display the status of the projector network.

1) Press as to select [NETWORK STATUS].

2) Press the <ENTER> button.

f The [NETWORK STATUS] screen is displayed.

[DHCP] Displays the status of use of the DHCP server.

[IP ADDRESS] Displays the [IP ADDRESS].

[SUBNET MASK] Displays the [SUBNET MASK].

[DEFAULT GATEWAY] Displays the [DEFAULT GATEWAY].

[DNS1] Displays the address of the preferred DNS server.

[DNS2] Displays the address of the alternate DNS server.

[MAC ADDRESS] Displays the [MAC ADDRESS].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PT-RS11K Seite 158

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PT-RS11K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info