Bedienungsanleitung Satel CA-10 (Seite 26 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

24 Installer Manual SATEL

The OUT4 and OUT5 outputs can also be used to control the NOKTON NR2-DSC radio

monitoring transmitter (NEMROD system – format PC16OUT). In such a case it is necessary

to change the operating mode of these outputs by activating a suitable option in the service

function FS5. During operation with the NOKTON transmitter, the outputs are used for

transmitting a number of data on the control panel state (zone alarms, fire alarms, troubles,

armed mode, etc.) and do not perform functions programmed with the standard service

functions.

When hooking up any equipment with a considerable current consumption (e.g.

a radio monitoring transmitter) to the control panel, their "+" should be

connected to the battery "+" (a fuse is recommended on the feeder cable).

The ground must be connected to any COM contact of the control panel, but not

directly to the battery "-". Connection of the common ground to the battery "-"

causes incorrect operation of the charging current limiter and quick discharge

of the battery but can even damage the control panel.

Connections of telephone line

If the control panel telephone communicator is used in the alarm system (for monitoring,

messaging or remote programming), it is necessary to connect telephone line to the control

panel. It should be led to a connector situated on the right side of the printed board. In order

to ensure proper messaging, the control panel must be directly connected to the line

(connectors designated as TIP and RING), and any other devices (telephone, telefax) – after

the control panel (connectors designated as T-1 and R-1). Such a connection will make it

possible for the control panel to fully engage the line for the time of calling, which prevents

the messaging function from being blocked by lifting the handset. Additionally, the telephones

connected after the control panel do not signal the dialing by the control panel.

Caution:

• Do not send telephone signals and alarm system signals by one multicore cable. This may

result in a damage to the system in case of a high-voltage punch-through from the

telephone line.

• Telephone terminals of the panel should be connected to PSTN lines only. Connecting to

ISDN lines may lead to damage of the equipment.

• System installer should give the necessary information on the way of connection with

telephone network to system owner.

Connection of voice synthesizer

Where the function of alarm messaging with

voice announcements is used, a voice

synthesizer must be connected to the control

panel.

The CA-10 panel interfaces with the SM-2

synthesizer. The synthesizer socket

(designated as: SM-2 VOICE SYNTHESIZER)

is situated on the right-hand side of the

printed board, between the telephone line

connector and the socket of OUT5, OUT6

outputs. The SM-2 synthesizer should be

directly plugged into this connector. It is fitted

with minijacks for playback of the message

and "monitoring" of the telephone line.

ground

low-frequency signal

release

tel. line monitoring

power supply +

control panel

board

Figure 15. Description of SM-2 voice

synthesizer connector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info