Bedienungsanleitung Satel CA-10 (Seite 28 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

26 Installer Manual SATEL

computer notifies the panel with a DTR signal of its readiness to receive data. Lack of this

signal is reported by the panel as a trouble of the RS-232 port.

After starting the DLOAD10 proprietary program (on the included CD), selecting the

appropriate communication port (CONFIGURATION window) and activating the FS112

service function in the control panel, it is possible to program the control panel from the

computer.

Connection of power supply

The control panel is permanently connected to the mains power supply. Hence, before you

start to work on the system cabling, make yourself familiar with the electrical installation in

the facility. In order to power the control panel, select a circuit where voltage is always

present. This circuit should be protected with an appropriate fuse.

Before connecting the control panel to its power supply circuit, you must turn

off voltage in that circuit.

Description of electrical connections to the CA-10 OBU housing:

1. Connect the 230 V alternating voltage leads to the transformer terminals marked

"AC 230 V".

2. Connect the output voltage wires of the transformer secondary winding to the "AC" (~18 V)

terminals on the control panel main board.

3. Connect the wire of the PE electric shock protection circuit to the terminal block situated

next to the transformer and marked with the ground symbol . This circuit should also be

connected to the control panel protective terminal.

Do not connect the "neutral" wire of the 230 V AC mains supply circuit to the

ground terminal. If there no separate electric shock protection circuit in the

facility, this terminal should be left free.

Control panel power-up starting procedure:

1. Connect the emergency power supply wires to the corresponding battery terminals (the

red one to the battery plus, the black one to the minus). The control panel will not start

on connecting the battery alone (without the mains power connected), however, it will

keep on working in case of the 230 V AC voltage trouble, provided it was already started.

2. Switch on the 230 V AC mains supply – the control panel start follows.

Connection of the power supplies in the prescribed order will permit correct functioning of the

power supply unit and the control panel electronic safety devices, thus avoiding damage to

the security system elements caused by possible installation faults.

Note: If it is necessary to completely disconnect the control panel power supply, the 230 V

alternating voltage should be disconnected first, then the battery. Re-connection of the

power supply is to be performed in the above mentioned order (the battery first, then

the 230 V alternating voltage).

As the control panel has no isolating switch to disconnect the mains supply,

it is important that the owner or the user of the security system be informed on

how the system is to be disconnected from the mains (e.g. by indicating the fuse

which protects the control panel supply circuit).

Starting the control panel

When all electrical connections are made and checked for correctness, you can proceed to

starting the system. It is recommended to begin the work with the control panel with no sirens

connected, as the load can exceed capacity of the power supply unit, thus making start of the

control panel impossible. The sirens can be connected after programming parameters of the

realized alarm system is completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info