Bedienungsanleitung Satel CA-10 (Seite 30 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

28 Installer Manual SATEL

If the described procedure is unsuccessful, the option of hardware access to the service

mode must have been disabled in the control panel by software means. If this is the case,

it is necessary to carry out another procedure which would enable the control panel and

restore the default settings:

1. Disconnect in turn the mains supply and the emergency supply.

2. Set a jumper on J19 RESET pins.

3. Connect in turn the emergency supply and the mains supply.

4. Wait about 60 seconds (±5 sec.) and remove the jumper.

5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15 seconds)

and confirm by pressing the [#] or [

] key.

Programming the control panel from the computer

Programming the control panel from the computer via the RS-232 port should be initiated by

calling the service mode and the FS112 communication function in the control panel.

Provision is also made for starting communication without calling the function FS112 – which

is convenient if the control panel is already installed on the site and there is no keypad in the

vicinity. In order to start communication without the use of keypad do the following:

1. Disconnect in turn the mains supply and the emergency supply.

2. Connect the cable to RS-232 ports in control panel and computer (Fig. 17).

3. Start the DLOAD10 program in the computer.

4. Select in the program the communication port to which the cable is connected.

5. Select in turn the following functions from the program menu: Communication; Local

connection with...; CA10 (RS-232, without the use of keypad).

6. Follow the messages displayed by the program.

ACTIVATING SELECTED FUNCTIONS

Performance of some functions of the control panel requires that a few to more than a dozen

parameters be programmed simultaneously. This section contains detailed information on

how to program such functions as: telephone messaging, monitoring and downloading.

Guard control function

The functioning of the guard control function consists in automatically checking that the,

so-called, guard code is entered on the keypad with a preset frequency. The entry of the

code is saved in the log event, and so is the trouble to enter the code after a preset period of

time, which can be signaled on an output which has the proper function. These events can be

reported to the monitoring station.

To activate the function you must:

• program the guard code – in the user function 2 (creating new user) a code with authority

level 5 (instead of the guard code, the user function 7 can also be used – activation of the

„switch MONO" output)

• set a suitable timer to perform the „partition monitoring” function (FS106)

• program the timer control time (functions FS102–FS105, depending on the partition).

Telephone messaging – alarm reporting

The telephone messaging function requires that the following be programmed:

• FS5, FS131 – activate the “telephone messaging” option, set the “dialing system” option

as required by the telephone exchange,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info