Bedienungsanleitung Satel CA-10 (Seite 31 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 29

• FS87 to FS94 – enter at least one telephone number,

• FS95 – define the partitions from which alarms are to be reported to the telephone

numbers programmed in functions FS87–FS90,

• FS100 – number of telephone messaging queues higher than zero and number of redials

in a queue.

Note: You should also program in FS95 what kind of message will be sent – if no message is

selected for the pager, the control panel will notify with a voice message from the voice

synthesizer.

When the above parameters are correctly programmed and the alarm is triggered, the on-

board LED (designated as „DIALER”) should go on, which indicates that the panel has

started telephone messaging (with pulse dialing the LED is blinking). It is recommended to

test the messaging. To this purpose, use the ordinary headset connected to the „telephone

line monitoring” jack in the SM-2 synthesizer (parallel connection of a telephone set to

„monitor” the communication will interfere with the messaging operation). The telephone

messaging will start immediately after triggering the alarm. Alarm clearing will interrupt the

telephone messaging.

Typical problems with starting the voice messaging:

• control panel takes no attempts to call – not all of the above mentioned items were

programmed;

• control panel goes on line but fails to dial – no dial tone or a non-standard dial tone

from the telephone exchange – find out the cause of missing signal or deactivate the dial

tone test option in FS5 if the signal is non-standard;

• control panel establishes connection, but sends no voice message – wrongly

programmed FS95 – messaging to pager selected, but not voice message from the

synthesizer;

• control panel establishes connection, sends a message too early or too late – the

control panel recognizes answering the call on the basis of sound signals on the telephone

line, with permissible message sending delay up to 4 seconds from lifting the handset – if

commutation signals on the telephone line are non-standard or there is strong interference

(clicks, hum), the panel automatic equipment may not function properly – then you can

extend the message by activating the “double message” option in FS5 or deactivate the

call answer recognition option;

• control panel reports the alarm more times than the preprogrammed number of

queues – the control panel recognizes answering the call on the basis of a callback signal

– if the user lifts the handset too quickly (during the first ring), the control panel may

disregard the message and call again.

Reporting to telephone monitoring station

The monitoring station operator should provide the installer with the data necessary for the

monitoring software. These are:

• monitoring station telephone numbers;

• transmission format or a list of available formats;

• alarm system identifier (facility number – one or more for detailed reporting from a big

system);

• list of event codes.

In order to start monitoring, the following items should be programmed:

• FS43 – monitoring station telephone number – if there are two numbers or two

stations, the other number should also be programmed in FS44.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info