Bedienungsanleitung Satel CA-10 (Seite 32 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

30 Installer Manual SATEL

• FS45, FS46 – station transmission formats – in case of a multi-format station, select

format which is as fast as possible (e.g. Ademco Express or Radionics 2300 with parity).

• FS47 – monitoring options.

• FS48 to FS59 – monitoring stations identifiers, an identifier should have 3 or 4 non-

zero characters (characters from “1” to “F”, “0” – no character), some stations use

identifiers composed from digits from 0 to 9 – then character “A” is to be programmed

instead of digit “0” (e.g. “A1A2” instead of “0102”).

At least three identifiers should be programmed (can be identical):

− zone identifier,

− partition identifier,

− system event identifier.

• FS60 to FS66 & FS69 to FS72, FS81, FS82, FS126 – event codes according to the list

from the monitoring station operator, the codes can be one-digit (the other character

being 0) or two-digit – as required by the station, the codes with inappropriate length may

block communication with the station.

• if reporting with event sorting to both stations has been selected in the options, events

assignment should be programmed in the functions FS67–FS68, FS73–FS80, FS83,

FS84.

• FS5 – activate the option “Monitoring” after the above items have been programmed.

Typical problems with starting the monitoring:

• Control panel takes no attempts to call – not all of the above mentioned items have

been programmed – the control panel will not call the monitoring station if the

programmed data do not allow sending a correct transmission to the station because of

e.g. missing telephone number, identifier being shorter than 3 non-zero characters,

missing event code, etc.

• Problems with dialing – no dial tone or a non-standard dial tone from the telephone

exchange – find out the cause of missing signal or disable the dial tone test option in

FS5 if the signal is non-standard.

• Control panel sends no codes when connected to the station – wrongly selected

format or low quality of telephone connection (the panel does not “understand” the

station dial tone).

• Station does not receive or acknowledge the codes sent by the panel – wrongly

selected format, inadequate identifier length (3 characters, while the station requires 4),

inadequate event code length (1 character, while the station requires 2) or low quality of

telephone connection.

• Control panel does not send codes of some events, despite of the codes being

properly entered – identifier of the particular group of events is missing, e.g., if the

partition 1 identifier is missing, no reports on this partition arming/disarming will be sent.

• Control panel automatically changes the option „transmission to Station 1 or to

Station 2” into transmission to one station only – if with this monitoring option

selected the number of identifiers for Station 1 and Station 2 is different (there are

codes which have an identifier for one station, but not for the other), the panel cannot

report to both stations in the „Station 1 or Station 2” mode and will change the option for

transmission to the station which has a larger number of identifiers.

Note: For the Ademco Express transmission format the identifier „0000” is correct (sending

"zero" is possible), while for the other formats it means no identifier ("zero" is not sent).

A headset connected to the "telephone line monitoring" jack in the SM-2 synthesizer can be

helpful in analyzing the problems with communication to the monitoring station.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info