Bedienungsanleitung Satel CA-10 (Seite 29 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 27

If the control panel operates with one keypad, having a default address (1001 – jumpers on

pins „A” and „D”), then, after the power is switched on, the keypad will report readiness for

work with four short beeps followed by a long one.

Note: The control panel with default settings will not support a keypad connected to the

CLK1 signal if the default address (1001) has been changed in that keypad.

If the control panel is alarming after power-up, clear the alarm by means of the user access

code (default master code for partition 1: [1][2][3][4]) and proceed to programming

parameters in the service mode.

Upon entering the default service code [1][2][3][4][5] and confirming it with the [#] key, the

control panel will enter the service mode. The

[ALARM] and [ARMED] LEDs will be

blinking alternately. Now, you can proceed to programming the control panel.

Note: For the safety reasons it is recommended that the keypad default address be

changed. Having done the changes, you must run the FS124 function.

If the system includes more keypads or where the zone expander is installed, the control

panel will not support any devices connected to the signals CLK2, CLK3, CLK4 until their

addresses have been programmed in the control panel memory.

Hardware access to the service mode

If the panel does not „see” the keypad when the power is on, and does not respond to the

keystrokes (access code entry), or keeps on alarming, it is necessary to carry out the

procedure of hardware access to the service mode. This allow to program of the

keypad/expander addresses before the normal operating mode is restored. In the other case,

the control panel will start alarming right after the power-up because it has detected the

keypad tampering.

To start the service mode by means of jumpers follow the procedure below:

1. Disconnect in turn the mains supply and the emergency supply.

2. Check the keypad address jumpers and tamper contacts for correct settings.

3. Put a jumper on the control panel RESET pins (J19).

4. Connect in turn the emergency supply and the mains supply.

5. After the keypad beep, remove the jumper from the RESET pins (J19). The operation

will activate the service mode in partition 1 keypad. This will be signaled by the

keypads with four short and one long beeps.

6. Call the service function FS124. The function automatically reads the keypad address and

prepares the control panel for work in a new configuration.

Note: If LCD keypads are installed in the alarm system, call the FS-124 service function

in each LCD keypad. When activated from the LCD keypad, this function automatically

performs additional configuring operations and its activation in each LCD keypad is

necessary for proper operation of the system.

7. To make sure that all the settings are in accordance with the default values, you can

perform the service functions FS107, FS108 and FS110.

Having completed the procedure, exit the service mode using the function FS0 and activate

the service mode again – this time from the keypad – by entering the default access code

[1][2][3][4][5] confirmed with the [#] key.

If the control panel has re-entered the service mode, it means that its functioning is correct

and that you may proceed with further installation of the system (connection of sensors,

sirens, establishing communication with a computer, if required) and programming of all

necessary parameters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info