Bedienungsanleitung Satel CA-10 (Seite 9 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CA-10 SATEL

In some keypads, the numeric keys are provided with letters. They may help the user

memorize a code by associating it with a particular word (e.g. the „[5][6][2][7][2]” code

corresponds to the word „KOBRA”).

When creating a new user access code, the master user assigns a so-called authority

level to it , i.e. determines which of the panel functions are available to the particular

user, and which are not. Usually, an access code entered for the particular partition will

only control that specific partition.

Optionally, the installer can activate the so-called "global access code" function. When

selected, this option makes the user access codes accepted in all 4 partitions,

irrespective of where they were entered, but the particular user number will not be

recorded in the event log.

Arming [CODE][#]

Arming is only possible when the partition is not signaling alarm and is not already

armed:

[

ALARM

] and [

ARMED

] diodes are off.

In order to arm the system access code should be entered and confirmed by pressing

[#] key. If, while typing the code, user makes a mistake, [

] key should be pressed and

the code re-entered. The access codes should be entered very carefully. Giving

a wrong access code three times in sequence may activate the alarm which is recorded

in alarm memory log as „3 wrong codes alarm”.

If the code is entered correctly and arming is possible, the panel will confirm the entry

with three short beeps. At the same time the [

ARMED

] LED will start blinking, which

indicates the exit delay time.

The LCD keypad will display information on arming, as well as the name of the user

who activated the armed mode. It will be followed by information on the exit delay

countdown (provided such an option is provided by the installer). The partitions with

active exit delay countdown are also indicated by blinking of the corresponding LEDs.

The exit delay and the way of audible signaling operation should be determined by the

installer.

The panel may fail to arm the system if:

• the panel is not ready for arming: there are specifically selected zones which

cannot be violated or tampered when the system is being armed and one of them

is violated or tampered at the time of arming - the panel will signal the situation

with three long beeps. In such a case, it is recommended to wait until all the zones

are ready (the LEDs 1-12 / 1-16 go out), and then arm the system again. If one of

the zones remains violated (one of the LEDs 1-12 / 1-16 is on, which may be

caused e.g. by a detector trouble) or tampered the armed mode can be activated

after bypassing that zone (with user function 4),

• the access code is wrong - the control panel will signal the event with two long

beeps

• the partition contains no armed type zones - the control panel signals the event

with two long beeps (access code is correct and allows, for example, to call user

functions)

• battery trouble - three long beeps (proper option is selected to prevent the

system from being armed in case of battery trouble).

Quick arming [0][#]

The user can quickly arm the system without any access code by pressing the [0][#] key

sequence. The Quick Arming function can be disabled by the installer. This way of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info