Bedienungsanleitung Satel CA-10 (Seite 10 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USER MANUAL CA-10

arming is not affected by any detectors being violated at the time. The installer can also

install a special key for quick arming of the system.

Disarming and clearing alarm [CODE][#]

When the control panel is armed ( [

ARMED

] LED is on or blinking) or signals an alarm

(

[

ALARM

] LED is blinking), it can accept only one command: disarming the system or

clearing the alarm. Entering the access code confirmed by pressing the keys [#] will

disarm the system or turn the alarm off. If, when entering the access code, the user

makes a mistake, he should press the [

] button and re-enter the code.

The panel confirms acceptance of the command by three short beeps and extinguishing

the [

ALARM

] and [

ARMED

] LEDs.

The control panel will not disarm the system or clear the alarm if:

• the access code is invalid,

• the access code authority level does not allow disarming (for example, authority

level 3 or 9 - see "User Functions" - "User add")

It is also possible to clear the alarm without disarming the system by using the authority

level 0 access code.

In the LCD keypad disarming the system is confirmed with an appropriate message on

the LCD display and the name of the user who armed the system. If the alarm has been

cleared the keypad will display the message "View (

ÇÈÅÆ

)" - the arrow buttons allow

viewing partition status to find out the source of alarm.

If the alarm system is divided into partitions, the alarm can only be cleared in the

partition whose keypad signals the alarm condition with the

[

ALARM

] LED.

Clock controlled arming / disarming

Arming and disarming of the system can be controlled by the control panel clock. The

installer can program the exact hour and minute of arming/disarming of the system.

Arming and disarming will occur every day at the specified time. The control panel may

also be armed with the clock only - then disarming will be done manually by the user.

System status telephone messaging

The owner of the facility where a CA-10 control panel is installed can check if there was

an alarm in the system by using a telephone. In order to do so, he has to call the

protected facility: the control panel will answer the call and inform about the system

status. The control panel will answer telephone calls only when the system in the entire

protected facility is armed.

When answering the call the control panel sends:

• one beep a second - if there was no alarm condition since the last arming;

• voice synthesizer message - if an alarm occurred within the last hour;

• sequence of five short beeps every second - if there was an alarm, but it

occurred more than an hour ago.

The panel can answer the calls in one of two modes:

• single calling mode - the panel answers the call after a specified number of rings

(as is the case with a standard answering machine); having answered a call, the

panel does not answer any more calls for 5 minutes;

• double calling mode - to get through to the panel, the user must call it and after

hearing a specified number of the so-called callback signals (1-second continuous

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info