Bedienungsanleitung Satel CA-10 (Seite 12 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USER MANUAL CA-10

Changing display mode of system state T key

Pressing and holding down the T key for about 3 seconds will temporarily change the

operating mode of LCD keypad: instead of displaying text messages on the system

status it will display the state of armed zones in LCD standard (and vice versa). The

keypad will automatically return to the operating mode specified by the installer after 40

or 140 seconds since the last key was pressed (depending on how the „long backlight”

option is set).

„HOLD DOWN” User Functions

The functions are available to any user (without using the access code). They are

activated by holding down the function key for about 3 seconds.

Switching to n partition (GOTO n) [1][2][3][4]

In the alarm systems divided into several partitions (subsystems), a single keypad

control over the whole system is possible. When depressed and held down, the keys

[1], [2], [3] or [4] switch over the partition the keypad is currently controlling. The control

panel will confirm receiving the command with three short beeps and the LED indicating

the partition served will start rapidly blinking if the partition is disarmed, or will be on with

steady light, if the partition is armed. Since that moment, the panel will recognize the

keypad the function was called from, as if it was connected to the given partition.

The LED keypad enables all the operations to be performed in this partition, except for

the „HOLD DOWN” function (the GOTO function cannot be called again).

The given partition is exited automatically (the keypad returns to its own partition after

approx. 15 seconds after the last key was depressed) or after depressing the [

] key for

3 seconds. The panel confirms the return to its basic partition with four short and one

long beeps.

Pressing the [

] key in order to exit the GOTO function is immediately confirmed with

two long beeps, and after 3-second holding down the key, return to the basic partition

ensues.

Note: If the panel does not confirm depressing the given key, it is already in its basic

partition and after three seconds it will call fire alarm from the keypad.

The LCD keypad makes it possible to switch over from one partition to another, and

then to return to the basic partition, by holding down the key with the number of next

partition (as distinct from the LED keypad, the [

] key does not switch over to the basic

partition). For example, when the keypad is connected to the first partition (which is its

basic partition), hold down the key [2] to switch the keypad to the second partition, then

hold down the key [3] to go to the third partition, and then hold down the key [1] to go

back to the basic partition.

Note: The above mentioned GOTO function is only available when enabled by the

installer.

Viewing alarms log [5]

By holding down the key [5] you can call the function which makes it possible to view

the alarms log.

In the LCD keypad, the following message will be displayed: „Viewing alarms log

(

ÇÈÅÆ

)”. Pressing any key will display a date, time and source of the last alarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info