Bedienungsanleitung Satel CA-10 (Seite 14 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USER MANUAL CA-10

10 - problem with transmission to monitoring station

11 - not used

12 - output 4 trouble

The previously detected troubles are displayed on repeatedly pressing any key. The

[

] key cancels the troubles log viewing function.

Current trouble check-out [7]

When the control panel signals a trouble detection (the

[

TROUBLE

] LED is blinking),

you can activate the current trouble check-out function by holding down the key [7].

In the LCD keypad, information on the trouble will be displayed When there are more

troubles, you can scroll through all the detected troubles list by pressing the keys WS

or TX.

In the LED keypad on activating the function, the (the

[

TROUBLE

] LED and the LEDs

indicating current troubles turn on (lack of illumination of any of the 12 LEDs is also

indicative of a problem). Pressing any key stops the function.

Note: If the installer has activated the "Indicate trouble until cancelled" option, the

trouble indicator will be on until cancelled, even if the trouble cause has been

removed. The trouble will be cleared after the trouble memory viewing is

completed and the function is quitted by pressing the [#] key. Quitting the

function by means of another key will not cancel blinking of the

[

TROUBLE

]

diode.

The LEDs have the following meanings:

1 - output 1 trouble,

2 - output 2 trouble,

3 - output 3 trouble - no load (e.g., the siren wires are cut), or overload (short

circuit) - usually service intervention is required.

4 - 230V AC loss - the panel is equipped with a limited time battery backup; if the

AC power loss trouble occurs despite of an effective AC mains, service

assistance should be called.

5 - battery trouble - to check on the type of battery trouble, press the key [5] – the

LED 1 or LED 2 will show the type of trouble:

- LED 1 – the battery is not connected or almost discharged or the fuse

on the control panel board is out of order,

- LED 2 – the battery voltage is too low (lower than 12V under load) –

discharged battery. This state may last for several hours after the

system has operated without the mains supply (or after a discharged

battery is connected). The battery charging time depends on its

capacitance (the battery is charged with direct current about 350mA,

the time necessary for testing the battery status is approx.12 minutes).

6 - keypad power supply trouble - signals an installation fault; service

intervention is necessary (the trouble can only be displayed while

viewing the trouble log).

7 – time not set - occurs on powering down and restarting the control panel; the

clock should be set with user function 6.

8 - printer trouble - stands for "not-ready" status of the printer connected to the

control panel RS-232 port as a result of, e.g., paper out trouble or no

power supply. The RS-232 port is monitored if the installer activates

real-time event printout.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info