Bedienungsanleitung Satel CA-10 (Seite 19 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

SATEL CA-10 17

Note: Options 7 and 8 of the third set are only relevant with activated option 7 of the second

set – „outputs OUT5, OUT6 control NOKTON radio messaging”.

FS6 - programming the global times (DEC)

The settings refer to the entry delay, exit delay and alarm time. The times are valid for the

entries and exits to which no individual times are assigned. The exit delay time is common

for all partitions. The alarm time programmed in this function refers also to the keypad

alarm signaling.

Note: The alarm time set with the function FS6 defines also the zone alarms cut-off time -

when the alarm is on, the subsequent zone violations will not trigger consecutive

alarms until the cut-off time has elapsed.

The time values are programmed within the range from 1 to 99 seconds.

In the LED type keypads, the values of entry time, exit time and alarm time are entered in

turn by two digits.

EXAMPLE (for the LED keypad):

programming the times: entry delay=30s, exit delay=60s, alarm=90s

[6] [#] - call the required function

[3][0] [#] - enter the entry delay time (two digits) – the LED 12 is blinking

[6][0] [#] - enter the exit delay time (two digits) – LED 11 is blinking

[9][0] [#] - enter the alarm time - the LEDs 11,12 are blinking - after acknowledging the last time, the

control panel automatically exits the function.

When programming from the LCD keypad, pressing the [#] key confirms all the three times

entered.

FS7 - programming the counting zone counters (DEC)

The control panel is equipped with three independent violation counters which can be

associated with any zones. Violation of these zones will trigger alarm after the programmed

number of violations is exceeded in the respective zone counter. Each counter can sum up

violations of one or several zones defined as the counting ones (e.g. the counter 1 can count

violations of zone 2, the counter 2 - violations of zones 4, 5, 6). The alarm will be generated

by the zone which has been violated as the last one.

Three counter values are programmed, from 01 to 07, in the following order: counter 1,

counter 2, counter 3. If no counting zones are provided in the panel, the programmed values

are irrelevant.

- Number „0” programmed – alarm after 8 violations.

- Number „1” programmed – alarm after the second violation.

- Number „2” or higher programmed – alarm after the number of violations equal to the

value programmed.

Time gates corresponding to the counters are programmed in FS123.

EXAMPLE (for LED keypad):

programming the counters: the 1

- 2 violations, the 2

- 5 violations, the 3

- not used

[7] [#] - call the function

[0][2] [#] - program the first counter (the lower LED B is blinking)

[0][5] [#] - program the second counter (the lower LED A is blinking)

[

] - exit the function - programming of the third counter is omitted

Functions programming partition assignment

FS8 - zones assignment to partition 1 (BIT)

FS9 - zones assignment to partition 2 (BIT)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info