Bedienungsanleitung Satel CA-10 (Seite 46 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

44 Programming SATEL

• start the DLOAD10 program on the computer and select the number of communication

port (COM);

• call the service mode in the panel and activate the function FS112.

Calling the function FS112 will be signaled by the panel with lighting the

[

TROUBLE

] LED.

If the panel receives no computer readiness signal within 10 seconds (due to an incorrect

computer connecting cable or port number) the function will be automatically exited.

The waiting for the computer command during an active connection is signaled by one short

beep every 10 seconds. When the connection is broken, the control panel quits the function

and enters the service mode.

Having entered the FS112 function, the keypad accepts no commands from keypad -

the control panel receives commands from computer. The function is exited after

sending a suitable command by the computer (while exiting the service mode). It is possible

to quit the function by pressing and holding down the [

] key for about 3 seconds.

It is possible to program the control panel from a PC computer without calling of the

function FS112 in the keypad (see: Installer Manual).

Functions related to memory of events

FS113 - event log printout (all events)

The control panel event log can be printed if a printer with RS-232 port is connected to the

control panel. The printout is started by calling the function. No DTR signal from the printer

will terminate the function and an error will be signaled (two short beeps). Holding down the

[

] key will stop the printout.

Note: Activation of the "printing on" option is not necessary - it regards a situation, when the

printer is connected permanently.

FS114 - alarm log printout

It operates in the same way as FS113, but alarms only are printed.

FS115 - trouble log printout

It operates in the same way as FS113, but troubles only are printed.

FS116 - partition event printout (arming/disarming)

It operates in the same way as FS113, but only arming and disarming events are printed.

Messaging – programming of messaging parameters

FS117 - permissible telephone line loss delay (DEC)

The function defines how many minutes may elapse from the low voltage condition on the

telephone line to the moment the panel reports a trouble. The programming consists in

entering a two-digit number from 00 to 99 minutes. If 00 is programmed, the panel will never

report a trouble.

EXAMPLE (for LED keypad):

programming a twenty-minute delay

[1][1][7] [#] - call the function

[2][0] [#] - program the delay

FS118 - parameters of pager station signals (HEX)

The function defines parameters of the answer signals generated by automatic pager station.

As different answer signals are used in each system, it is necessary to specify the signal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info