Bedienungsanleitung Satel CA-10 (Seite 48 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

46 Programming SATEL

[#] - confirm the counter 1 count-up time and proceed to programming counter 2

[1][5][0] - enter the count-up time for counter 2 (LED 11 is blinking during programming)

[#] - confirm the counter 2 count-up time and proceed to programming counter 3

[2][5][5] - enter the count-up time for counter 3 (LEDs 11 and 12 are blinking during programming)

[#] - confirm the counter 3 count-up time and quit the function

In the LCD keypads, the keys ▲ and ▼ scroll the list of counters for which a defined time

value is entered from the numeric keypad.

Special Functions

FS124- keypad address auto-detect

The function enables the keypad addresses to be automatically detected without changing

the other parameters.

In the LCD keypad, the function FS124 performs additional configuration operations, hence,

after each modification of the configuration (adding or deleting keypad and/or expander) it is

necessary to call the FS124 in each LCD keypad connected to the control panel.

FS125- testing outputs

The function makes it possible to check that all the wiring of control outputs for signaling

devices or other equipment is properly connected. For functional check of an output, call the

function and press the key with number of the output (1-6). Enabling the output is

acknowledged with two short beeps, and, in the LED keypads, also by lighting a LED with

the output number, and in the LCD keypads - by displaying the output number. The output

will be disabled by pressing again the key with the output number (one short beep and

extinguishing of the LED in LED type keypads or disappearing from the display of the output

number in the LCD keypads).

Calling the function will disable all the active outputs (if they have been active), while quitting

the function will reset the same. If the outputs OUT5 and OUT6 are functioning in the „radio

messaging control” mode (FS5 option 7 of the second set), the function will not make them

available for testing.

Monitoring - programming system reporting codes

FS126- programming guard control codes (HEX)

The function is used for programming the system events codes - set III. This codes are sent

to monitoring station with system events identifier. The rules of programming the partition

codes of guard are identical with those for zone event codes. The codes may be extended

by the user number (see: FS47) based on the same principles, as the zone event codes may

extended by the zone number.

The list of events and LED signaling in LED type keypads:

Number LEDs 9-12 Event

1  Code of guard in partition 1

2  Code of guard in partition 2

3  Code of guard in partition 3

4  Code of guard in partition 4)

5  Code of lack of guard in partition 1

6  Code of lack of guard in partition 2

7  Code of lack of guard in partition 3

8  Code of lack of guard in partition 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info