Bedienungsanleitung Satel CA-5 Plus (Seite 12 von 27) (Englisch)

699583

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Installer Manual CA-5

• It is recommended that the cable be connected first to the control panel connector, and

then to the computer connector.

3. The JP1 „RESET” pins – make it possible to start the service mode without entering any

service code. This function can be disabled by the installer with the software means (see:

FS 9 – Option 1).

4. The „DIALER” LED – it is lit up during telephone messaging by the control panel, and

blinks during pulse dialing.

Next to the LED is situated an adjustable resistor. Its setting should not be

changed, since it would cause incorrect work of the dialer (loss of the capability

of dialing in the DTMF system and monitoring in the „Ademco Ex” and „Contact

ID” formats).

BOARD TERMINALS:

AC – module power supply inputs (18 V AC ± 10%)

Z1 to Z5 – zones

OUT1 – signaling output (current-carrying capacity 1.1 A)

OUT2, OUT3 – control panel programmable outputs (current-carrying capacity 50 mA)

DATA, CLK – keypad bus terminals

KPD – keypad power supply output (+12 V)

AUX – detectors power supply output (+12 V)

COM – common (0 V)

– protective terminal – ground (connect to protective circuit only)

TIP, RING – external telephone line terminals

T-1, R-1 – internal telephone line terminals (telephone set connection)

The AC terminals are intended for the supply of alternating voltage from the mains

transformer. The control panel power supply is suitable for operation with the input voltage of

18 V AC ± 10%. The control panel is fitted with an advanced pulse-type power supply of high

energy efficiency and operational reliability, the correct functioning of which requires,

however, that the input voltage at the maximum load of the transformer by the control panel

never drop below 16 V AC.

The control panel power supply (current efficiency 1.2 A) is fitted with:

• voltage stabilization system (the voltage value of 13.6 V–13.8 V DC is factory set during

production process and should not be changed);

• battery status monitoring system with optional disconnection of the battery if discharged

- during testing the processor reduces the power supply voltage to about 10.5 V and the

consumers are powered from the battery. The testing takes place every 4 minutes and

lasts for less than twenty seconds. If the battery voltage drops down to about 11 V, the

control panel will report a trouble. In case of the voltage fall to 9.5 V, the control panel will

cut off the battery in order to prevent it from being completely discharged and damaged.

Attention should be paid so as not to cause overloading of the control panel power supply in

the security system. It is advisable to make a load balance for the power supply. The total

current inputs for the consumers (detectors, keypads) and the battery charging current may

not exceed the power supply capacity. In case of a higher electric power demand, an

additional power supply can be used for some of the security system consumers

(e.g.: APS-15, APS-30 manufactured by SATEL). Table 1 (at the end of this manual) shows

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Plus Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info