Bedienungsanleitung Satel CA-5 (Seite 9 von 24) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CA-5 SATEL

4.6.2 Silent armed mode

The supervision mode during which the alarms are transmitted to the monitoring station,

signaled in the keypad, and on the K

EYPAD ALARM

type of output.

4.6.3 Partial armed mode with no exit from the site

The armed mode with automatic bypassing of the zones (detectors) assigned by the

installer. If, after arming the system, the user has not left the site and has not violated

the entry/exit monitoring line during the exit delay, the selected zones of the control

panel will be automatically bypassed, and activation of the detectors connected to those

zones will trigger no alarm.

4.7 A

RMING

[CODE][#]

The arming is only possible when the system is signaling no alarm and it is not in the armed

mode: the [ALARM] and [ARMED] LEDs are off.

In order to arm the system, enter the user access code and confirm it with the [#] key. If you

made a mistake when entering the access code, press the [

] key and re-enter the code. The

access codes should be entered very carefully. Three consecutive mistakes may trigger the

alarm recorded in the events log as the „3 wrong codes alarm”.

If the code is entered correctly and arming is possible, the control panel will confirm the entry

with four short beeps followed by a long one and will get armed. In case the installer has pre-

programmed the „exit delay”, the [ARMED] LED will start blinking to indicate beginning of

that time countdown, and arming will take place when the countdown is over. The LCD

keypad will display information about exit time delay.

The installer determines the length of the exit delay and the way the audible signaling works.

EXAMPLE: Arming with the user access code: 39763.

press in turn: [3][9][7][6][3] [#]

The control panel may fail to arm the system if:

• the panel is not ready for arming the system: there are zones defined by the installer

which must not be violated or tampered while the system is being armed („

PRIORITY

”

option) and one of them is being violated or tampered – the panel signals this state with

three long beeps and displays the names of violated zones on LCD keypad.

In such a situation, you should wait until all the zones are ready (in the LED keypad the

LEDs 1÷5 will go out; in the LCD keypad – symbols of zone violation) and then arm the

system again (enter the access code). If, for example, one of the zones remains all the

time violated (in the LED keypad one of the LEDs 1÷5 is always on, in the LCD keypad the

symbol of zone violation is displayed – it may be caused e.g. by the detector failure), the

armed mode can be activated after bypassing the given zone (using the function 4);

• the access code is incorrect – this situation is signaled with two long beeps.

• at least one output in the system performs the D

URESS ALARM

function and is on (active).

Using the code which does not carry out the „action under duress” function will reset the

a.m. output activity (three short beeps) without arming the system; the system will only be

armed on using any code again.

4.8 Q

UICK ARMING

[0][#]

Quick arming without using any access code is possible by consecutive pressing of two

keypad keys:

EXAMPLE: [0][#] – arming

The control panel cannot arm the system when:

• an alarm condition is signaled by the panel (the [ALARM] LED is blinking);

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info