Bedienungsanleitung Satel CA-5 (Seite 8 von 24) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

SER

ANUAL

CA-5

4.4 E

VENTS SIGNALED ON THE

OUT1

OUTPUT

The installer may activate the signaling of arming/disarming and alarm clearing on the OUT1

output. If this output controls the siren operation, it will generate short sounds (in much the

same way as in the car alarm systems). The signals have the following meanings :

• one short sound – arming,

• two short sounds – disarming,

• four short sounds – clearing the alarm or disarming and clearing the alarm.

Additionally, the OUT1 output signals the typical situations for the security system:

• continuous signal – burglary alarm,

• intermittent signal 1s/1s – fire alarm.

The installer may select the identical manner of signaling for the fire alarm and for the

burglary alarm (i.e. the continuous signal), he can also, with the use of a corresponding

service function, disable the OUT1 output signaling of arming/disarming from the keypad.

4.5 U

SER ACCESS CODES

For everyday operation of the system it is necessary to know the user access code (the

access code is a sequence of 4 to 8 digits within the range of 0–9).

To enter the access code in the control panel, press the corresponding keys on the keypad in

the order of the code digits and finish the full sequence by pressing the [#] or [

] keys (as may

be required). The control panel comes with the following factory settings:

master user access code: 1234;

service code: 12345.

By using the master user code you can program 5 additional user access codes, or to

delete them if they were programmed before.

The installer can assign specific authority levels to some of the access codes to distinguish

them from the other user codes:

• Access code No. 4 – action under duress (disarming or alarm clearing by means of this

code results in sending a special code to the monitoring station, and activating the D

URESS

ALARM

output)

− access code cannot be changed with the user function 1;

− the code does not reset activity of the D

URESS ALARM

output.

• Access code No. 5 - does not disarm for other users – permits disarming only when the

same access code was used for arming the system, which makes it possible to control

(block) access to the site for the user who has such an access code at his disposal.

The installer has access to some of the user functions (service code ending with [

]).

However, the service code cannot arm and/or disarm the system, set the service access time

and add or delete the users.

4.6 A

RMED

ODE OF THE

ONTROL

ANEL

In order to adjust the security system to various situations, the CA-5 control panel offers

several armed modes:

4.6.1 Full armed mode

The operating mode when detectors connected to the control panel control the

protected site and violation of the protected areas is signaled by the control panel with

any available means (monitoring, sirens, keypad).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info