Bedienungsanleitung Satel CA-5 (Seite 17 von 24) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CA-5 SATEL

EXAMPLE: deleting the third and fifth user's access codes (Master user code = 7890).

[7][8][9][0][

] – calling the "user function" mode, confirmed with three short beeps and in the LED

keypad additionally slow blinking of the [PROGRAM] LED,

[3] [#] calling the "erase user" function, confirmed with two short beeps, and in the LED

keypad additionally with lighting up of LEDs with the numbers of existing codes (e.g.

1,2,3,4,5) and with fast blinking of the [PROGRAM] LED (in the LCD keypad this

function may be called using arrow keys),

[3][5] – indicating the numbers of deleted access

codes – confirmed in the LED keypad by

extinguishing of the LEDs with numbers 3

and 5 (the LEDs 1, 2 and 4 are still lit up),

and in the LCD keypad by disappearing of

digits 3 and 5 from the display (digits 1, 2

and 4 are still on),

[#] – deleting the selected access codes; four short beeps and a long one signal end of the

function.

6.5 B

YPASS ZONES

[CODE][

][4][#]

The function enables bypassing of the zones in order to arm a part of the system or to

bypass malfunctioning detectors in the armed mode.

After calling the function, press the keys with numbers corresponding to the numbers of

zones to be bypassed (the LEDs or digits corresponding to the selected zones will on) and

confirm the selection with the [#] key.

After bypassing the zones and quitting the user function mode in the LED keypad, the

corresponding LEDs start slowly blinking, in the LCD keypad letters “b” will appear on the display

in the fields corresponding to the bypassed zones. The zones will remain bypassed until the next

disarming or their manual unbypassing with the same function. The unbypassing consists in

extinguishing the LEDs (digits) which correspond to the bypassed zones.

Bypassing/unbypassing a zone generates an event saved in the control panel memory.

Upon arming, the indication of bypassed zones is switched off.

Bypassing the Arm/Disarm type zones makes impossible the remote arming/disarming of the

system, as well as the alarm clearing. This operation must then be performed by entering the

access code from the keypad.

EXAMPLE: bypassing the zones 3 and 4 (user access

code = 12321).

[1][2][3][2][1] [

] – calling the "user function"

mode, confirmed with three short beeps and

in the LED keypad additionally with slow

blinking of the [PROGRAM] LED,

[4] [#] – calling the "bypass zones" function,

confirmed with two short beeps (in the LCD

keypad this function may be called using

arrow keys),

[3][4] – selecting the numbers of zones to be

bypassed – in the LED keypad the LEDs 3

and 4 will light up, in the LCD keypad digit 3

and 4 will be displayed,

[#] – accepting the entered data – four short beeps and a long one signal end of the

function.

Note: The 24h zones (which are on duty, whether the system is armed or not) can only be

bypassed by means of the zone bypassing function, accessible on entering the service

code which ends with [

Whom to leave?

What to bypass?

8 Jul, 12:23:40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info