Bedienungsanleitung Satel CA-5 (Seite 18 von 24) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

SER

ANUAL

CA-5

6.6 A

ILENT

[CODE][

][5][#]

In the silent armed mode, the alarms are not signaled on the OUT1 output and on the output

programmed as

BURGLARY ALARM

. They are only signaled in the keypad and by sending

a message to the monitoring station.

EXAMPLE: activating the silent armed mode (user code = 1230).

[1][2][3][0][

] – calling the "user function" mode, confirmed with three short beeps and in the LED

keypad additionally slow blinking of the [PROGRAM] LED,

[5] [#] – activating the silent armed mode – four short beeps and a long one signal the end of

the function (in the LCD keypad this function may be called using arrow keys).

Note: If a zone with activated P

RIORITY

option is violated or tampered, than the control panel

will refuse to perform this function.

6.7 S

ET TIME

[CODE][

][6][#]

The function permits setting the control panel clock (day, month, hour). Present year is set by

the installer with the service function. The real indications of time and date ensure correct

interpretation of the events recorded in the panel memory log. The history of events may be

downloaded by means of the LCD keypad or the computer and its program managing the

CA-5 alarm control panel.

The programming procedure is as follows:

- HOURS, MINUTES – acknowledge ([H][H][M][M][#]),

- MONTH, DAY – acknowledge ([M][M][D][D][#]),

The hour should be given in the 24-hour format (with "zero" before the hour less than 10).

It is possible to leave the function earlier after programming the time (the date will remain

unchanged) by pressing the ([#]) key twice.

Note: In order to reset the „Clock loss” trouble signal, the time and date must be

programmed.

EXAMPLE: programming time: 7:45

and date: 25 July. (user access code = 1230)

[1][2][3][0][

] – calling the "user function" mode, confirmed

with three short beeps and in the LED

keypad additionally with slow blinking of the

[PROGRAM] LED,

[6] [#] – calling the “set time” function confirmed with

two short beeps and in the LED keypad

additionally with fast blinking of the

[PROGRAM] LED (in the LCD keypad

this function may be called using arrow

keys),

[0][7][4][5][#] – entering the hours and minutes confirmed

with two short beeps,

[0][7][2][5][#] – entering the month and day confirmed with

four short beeps and a long one, quitting the function.

The LCD keypad display present time, but in the LED keypad it is possible to check the

current hour and date set in the control panel. In order to check the settings, call the user

function 6 and pressing the [

] key twice look through the digits displayed on the LEDs (from

2 to 5) as they were programmed. The first digit is displayed immediately on calling the

function.

Time (hh:mm):

07:45

Date (mm.dd):

07.25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info