Bedienungsanleitung Satel CA-6 (Seite 15 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA-6 SATEL 13

• It is recommended that the cable be first connected to the control panel, and then to

the computer.

4. The „DIALER” LED – is on during telephone messaging by the panel, and blinks during

pulse dialing of the telephone number.

BOARD TERMINALS:

AC – module power supply inputs (18 V AC ± 10%)

Z1 to Z6 – zones

OUT1 to OUT3 – programmable outputs (current-carrying capacity 2.2 A)

OUT4, OUT5 – programmable outputs (current-carrying capacity 50 mA)

DATA, CLK – keypad terminals

CTL – control input

+KPD – keypad power supply output (current-carrying capacity 1.5 A)

+12V – power supply outputs

COM – common ground

– protective terminal – ground (connect to protective circuit only)

TIP, RING – terminals of outside telephone line

T-1, R-1 – terminals of extension telephone line (telephone set)

The AC terminals are intended for providing the alternating supply voltage from the mains

transformer. The control panel power supply unit is suitable for the 18 V ± 10% AC input

voltage. The control panel is fitted with an advanced pulse-type power supply of high energy

efficiency and operational reliability, however, its correct functioning requires that the input

voltage at the maximum load of the transformer by the control panel does not drop below

16 V AC.

The CA-6 main board enables a grounding circuit to be connected. The ground lead terminal

is designated by the symbol.

The control panel power supply (current capacity 1.2 A) is fitted with:

• voltage control system (the stabilized voltage of the control panel power supply is

+13.6 V to +13.8 V and is factory set),

• battery status monitoring system with optional disconnection of the battery if

discharged – during testing the processor reduces the power supply and the loads are

powered from the battery. The testing takes place every 4 minutes and lasts for less

than twenty seconds. If the battery voltage drops down to 9.5 V, the control panel will

cut off the battery in order to prevent it from a complete discharge and damage.

Attention should be paid so as not to cause overloading of the control panel power supply in

the alarm system. It is advisable to make a load balance for the power supply. The total

current inputs for the consumers (detectors, keypads) and the battery charging current may

not exceed the power supply capacity. In case of a higher electric power

demand, an additional power supply can be used for some of the

security system consumers (e.g. APS-15, APS-30 manufactured by

SATEL). The Table 1 (at the end of this manual) shows an example of

estimated balance of current consumption by the system, and an

example of battery selection.

Each of the high-current outputs OUT1 – OUT3 and +KPD is fitted with

electronic short-circuit and overload protection devices.

Two wires (red and black) are intended for connecting the battery, the

red one is connected to the battery „+” terminal, the black one to the „-”

terminal. The battery cables lugs should not be cut off.

The RS232 TTL interface is designed for programming the alarm

system parameters from a computer. The panel sends and receives

PRESS IN

BEND ASIDE

Fig. 3.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info