Bedienungsanleitung Satel CA-6 (Seite 16 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

14 SATEL Installer Manual

signals in the TTL (0 V, +5 V) standard, hence, a special cable of SATEL manufacture must

be used to connect the panel and computer RS ports. The cable includes a converter

changing this signal into a standard corresponding to the RS-232 interface in the computer

(-12 V, +12 V). The data can be transmitted through the cable in both directions.

The CA-6 control panel should be installed in an enclosed space with normal humidity of air.

The space should be fitted with an available permanent (not detachable) 230 V power supply

circuit with protective grounding.

The control panel can be mounted in the CA-6 OBU housing (this housing comprises

a transformer designed for operation with the control panel power supply), which permits

installation of a battery with 7 Ah capacity. Before the housing is secured to the base, it is

necessary to mount inside the housing plastic distance plugs, which are intended for

subsequent installation of the mainboard.

In case the plugs tend to slip out, the catches fixing the plug in the housing need to be slightly

bent aside (Figure 3). When inserting the plug, press the central part of the head firmly in so

that it is blocked in the housing hole. It is advisable to make sure that the plug, when

pressed, does not slip out from the opening. During installation of the housing, be careful so

as not to damage the wires which will be passed through the hole in its back panel.

When the housing is secured, you can install the control panel main board and proceed to

making the connections.

IMPORTANT: Do not connect the mains power supply and the battery, until all the remaining

connections are completed.

The control panel is power supplied from 230 V AC mains. Negligence or wrong

connection may result in electric shock and pose a threat to life!

Therefore, be particularly careful when hooking up the control panel. In the

process of installation and connection of the control panel, the cable to be used

for mains supply must not be alive!

Connection of keypad

The keypad should be connected to the system with a four-wire line, using the COM, +KPD,

DATA, CLK terminals on the panel. Where standard wire is used, the cable length can be up

to 200 m. Do not use screened wires.

It is recommended to use an untwisted unshielded cable 8x0,5 mm

(do not use twisted pair

cables). With recommended cable, the following distances between keypad and control panel

may be used to ensure appropriate power supply:

Distance Lead No. of cores

to 100 m

Supply and common ground

CLK and DATA signals

2 x 1

from 100 m

to 200 m

Supply and common ground

CLK and DATA signals

2 x 2

2 x 1

The keypads may only be supplied from the +KPD connector of the control panel. This

output can also be used to supply detectors connected to the keypads, if the total current

value of 1.5 A is not exceeded.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info