Bedienungsanleitung Satel CA-6 (Seite 26 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

24 SATEL Installer Manual

• control panel reports the alarm more times than the preprogrammed number of

rounds – the control panel recognizes answering the call on the basis of a callback signal

– if the user lifts the handset too quickly (during the first ring), the control panel may

disregard the message and call again.

Reporting to telephone monitoring station

The monitoring station operator should provide the installer with the data necessary for the

monitoring software. These are:

• monitoring station telephone numbers,

• transmission format or a list of available formats,

• alarm system identifier (facility number),

• list of event codes.

In order to start monitoring, the following function should be programmed:

• FS43 – monitoring station telephone number – if there are two numbers or two stations,

the second number should be programmed in FS44.

• FS45, FS46 – station transmission formats – in case of a multi-format station, select

format which is as fast as possible (e.g. Ademco Express or Radionics 2300 with parity).

• FS47 – monitoring options.

• FS48 to FS54 – monitoring stations identifiers, an identifier should have 3 or 4 non-zero

characters (characters from “1” to “F”, “0” – no character), some stations use identifiers

composed from digits from 0 to 9 – then character “A” is to be programmed instead of digit

“0” (e.g. “A1A2” instead of “0102”.

• FS60 to FS65 & FS69 to FS70, FS81, FS82, FS126 – event codes according to the list

from the monitoring station operator, the codes can be one-digit (the other character

being 0) or two-digit – as required by the station, the codes with inappropriate length may

block communication with the station.

• if reporting with event sorting to both stations has been selected in the options, events

assignment should be programmed in the functions FS67, FS68, FS73, FS74, FS77,

FS78, FS83, FS84.

• FS5 – activate the “Monitoring” option if the above functions are programmed.

Note: In order to make monitoring possible when the control panel is in the downloading

mode, it is necessary to terminate communication by using the „Quit communication”

command in the „Communication” menu of the DLOAD10 program.

Typical problems with starting the monitoring:

• Control panel takes no attempts to call – not all of the above mentioned functions have

been programmed – the control panel will not call the monitoring station if the programmed

data do not allow sending a correct transmission to the station because of e.g. missing

telephone number, identifier being shorter than 3 non-zero characters, missing event code,

etc. The control panel does not make any call attempts also when it is in the computer

downloading mode;

• Problems with dialing – no dial tone or a non-standard dial tone from the telephone

exchange – find out the cause of missing signal or disable the dial tone test option in FS5

if the signal is non-standard;

• Control panel sends no codes when connected to the station – wrongly selected

format or low quality of telephone connection (the panel does not “understand” the station

dial tone);

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info