Bedienungsanleitung Satel CA-6 (Seite 24 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

22 SATEL Installer Manual

Entering service mode "from pins"

If the panel does not „see” the keypad when the power is on, and does not respond to the

keystrokes (access code entry), or keeps on alarming, it is necessary to carry out the

procedure of hardware access to the service mode. This allows to program keypad

address before the normal operating mode is restored. In the other case, the control panel

will start alarming right after the power-up because it has detected the keypad tampering.

This procedure is also required when the keypad address is changed – it is necessary to

program the address first (see: FS111 or FS124). Otherwise, the control panel may start

alarming just after power-up because a keypad tamper has been detected.

To start the service mode by means of jumpers follow the procedure below:

1. Disconnect in turn the AC supply and the battery.

2. Check the keypad address jumpers and tamper contacts for correct settings.

3. Place the jumper on RESET (J13) pins located on the control panel board.

4. Connect in turn the battery and the AC supply.

5. After a minute remove the jumper from RESET (J13) pins – the control panel should

automatically enter the service mode. This will be signaled by the keypads with four short

and one long beeps.

6. Call the service function FS124. The function automatically reads the keypad address and

prepares the control panel for work in a new configuration. You can also restore the factory

default settings (FS107), restart the user passwords (FS110), and/or reset the event log

(FS108).

Note: Shorting the pins and power-up alone will restore no parameters! These

operations will call up the service mode, thus making it possible to program any

parameters required.

Having completed the procedure, exit the service mode using the function FS0 and activate

the service mode again – this time from the keypad – by entering the default access code

[1][2][3][4][5] confirmed with the [#] key.

If the control panel has re-entered the service mode, it means that its functioning is correct

and that you can proceed with further installation of the system (connection of sensors, sirens

or establishing communication with a computer, if necessary) and programming of all

required parameters.

If the described procedure is unsuccessful, the option of hardware access to the service

mode must have been disabled in the control panel by software means (see: FS131).

If this is the case, it is necessary to carry out another procedure which would enable the

control panel and restore the default settings:

1. Disconnect in turn the AC supply and the.

2. Set a jumper on RESET (J13) pins.

3. Connect in turn the battery and the AC supply.

4. Wait for a 60 seconds and then remove the jumper.

5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15 seconds)

and confirm by pressing the [#] or [

] key – the control panel enters the service mode.

ACTIVATING SELECTED FUNCTIONS

Performance of some functions of the control panel requires that a few or more parameters

should be programmed. This section contains detailed information on how to program such

functions as: guard control, telephone messaging, monitoring and downloading.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info