Bedienungsanleitung Satel CA-6 (Seite 23 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA-6 SATEL 21

Before connecting the control panel to its power supply circuit, make sure that

the supply circuit is not alive.

Description of electric connections for CA-6 OBU housing.

1. Connect the 230 V alternating voltage leads to the transformer terminals marked

"AC 230V".

2. Connect the terminals of the transformer secondary winding to the "AC" (~18 V) terminals

on the control panel mainboard.

3. Connect the wire of the electric shock protection circuit to the terminal block installed next

to the transformer and marked with the ground symbol . This circuit should also be

connected to the control panel protective terminal.

Never connect the "neutral" wire of the 230 V AC mains supply to the ground

terminal. If there is no separate electric shock protection circuit in the facility,

leave this terminal unconnected.

Control panel power supply starting procedure.

1. Connect the backup power supply wires to corresponding battery terminals (red to battery

plus, black to battery minus). The control panel will not start after connecting the

battery alone (without mains power supply) but it will operate in case of 230 V AC failure

provided that it was started earlier.

2. Switch on the 230 V AC mains supply – the control panel start follows.

Connection of the power supplies in the prescribed order will permit correct functioning of the

power supply unit and the control panel electronic safety circuits, thus avoiding damage to

the security system elements caused by possible installation faults.

Note: Should it be necessary to completely disconnect the control panel power supply

(the mains and the battery), re-connection of the power supply is to be performed in

the above mentioned order (the battery first, then the 230 V alternating voltage).

As the control panel has no isolating switch to disconnect the mains supply, it

is important that the owner or the user of the security system be informed on

how the system is to be disconnected from the mains (e.g. by indicating the fuse

which protects the control panel supply circuit).

Starting the control panel

When all electrical connections are made and checked for correctness, you can proceed to

starting the system. It is recommended to begin the work with the control panel with no sirens

connected. Sirens can be connected after alarm system parameters programming is

completed.

If the control panel operates with a keypad, having a default address (1001 - jumpers on pins

„D” and „A”), then, after the power is switched on, the keypad will report readiness for work

with four short beeps followed by a long one.

Note: The control panel with default settings will not support a keypad if the default address

(1001) has been changed in that keypad.

If the

[ALARM] diode is blinking, cancel it by entering the MASTER code [1][2][3][4] and

pressing [#]. Then, enter the default service code [1][2][3][4][5] and confirm it with the [#] key.

The control panel will enter the service mode, the

[POWER] and

[PHONE] diodes

alternately blinking. At this moment, you can proceed to programming the control panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info