Bedienungsanleitung Satel CA-6 (Seite 29 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA-6 SATEL 27

Remote communication:

• connect the telephone line to the TIP and RING terminals,

• program in the control panel:

− FS2: panel communication password (identifier by which the program recognizes the

alarm system),

− FS3: computer communication password (identifier by which the control panel

recognizes the computer authorized to connect to panel),

− FS4: computer telephone number (which is not necessary but ensures a better

protection against unauthorized access),

− FS5: “external downloading” option, “double call” option (any setting) and the FS101

– number of rings before answer – if communication is to be initiated from the PC.

• start the DLOAD10 program, select the control panel type (e.g. by opening the data of

such a panel) and, from the menu “Communication”, select the “Modem” item and the

„remote” connection mode;

• apart from the communication codes, conformity is also required between the above

mentioned options in the control panel and the security system data in the computer.

It is also possible to initialize communication with the panel with the user function 0.

Having established connection, read the control panel data and then you can proceed to

reading the events, programming parameters, etc.

Messages on troubles during modem initialization:

• „modem not responding” – a technical problem with communication with the modem,

e.g. an incorrect COM port number, conflict with the Windows system drivers.

• „initialization error” – wrong command initializing the modem.

Correct initialization of the modem does not mean it is properly configured to work with the

control panel. The first initializing commands, as suggested in the program, are sufficient

for a correct operation of most older-generation modems (i.e. modems with a maximum

speed of 2400 Bps). The fast modems of a new generation require some extra commands

being added to limit their operation speed.

Messages on telephone communication errors:

• „modem not responding” – the modem has not acknowledged the dialed number

(a rare occurrence, usually a problem caused by modem hardware or e.g. missing the

“V1” initializing command),

• „connection failed”, „no control panel signals”, „poor quality of connection, no

control panel handshake”

− connection with the control panel was unsuccessful,

− the control panel picked up the phone but did not answer because the modem

signal was corrupted,

− the control panel went off-hook, but did not answer the modem signal, because it

was neither V.21 or BELL 103 transmission format (incompatible or wrongly

configured modem),

• „communication password not acknowledged” – the control panel established

connection, but the computer communication password does not correspond to the one

programmed in the control panel in FS3 function – the panel disconnects,

• „connection interrupted” – the control panel stopped answering the computer signals.

Note: If the control panel answers the call but fails to establish communication and

disconnects, while the “double call” option is deactivated, it will be answering no

calls for the next 5 minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info