Bedienungsanleitung Satel CA-6 (Seite 6 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

General

The CA-6 control panel is characterized by a high flexibility of firmware, which enables their

functionality to be customized as per individual requirements of the protected premises.

Additionally, some extra functions can be assigned to the panel (for example, control of

lighting, locks, cameras).

The control panel can be configured from the keypad (locally) or by the computer with

a suitable firmware (locally via RS-232 port or remotely via modem). Programming with the

keypad is possible after starting the service mode. When programming from the keypad,

you should pay attention to information shown by means of the LED indicators and audible

signals.

Service mode [SERVICE CODE][#] or [SERVICE CODE][

]

The service mode can be started from the keypad in any disarmed and non-alarming

partition. In order to start the service mode, enter the service code (by default=[1][2][3][4][5])

and confirm it with the key [#] or [

]. The service mode is indicated by alternate blinking of the

[

POWER

] and the

[

PHONE

] LED and a short beep generated every 3 seconds (in the

CA-6 KLED-S keypad blinks LED designed ). No keypad tamper contact or address is

checked in the service mode. The service mode is on until deactivated by the service function

(FS0).

Programming the control panel service functions from keypad

The panel programming is based on three types of functions: bit (BIT), decimal (DEC) and

hexadecimal (HEX). The bit functions are used to program two-state parameters: YES and

NO (e.g. the functions of zone assignment to partition, options). The decimal functions are

used for programming a few digits data (for example, the test transmission time – 4 digits).

The hexadecimal functions are used to program hexadecimal data (e.g., monitoring codes).

During programming, if the functions have a several options (e.g., FS5, FS27), the number of

options set or the number of zone is shown on the

[

ALARM

AB] and

[

ARMED

AB] LEDs.

Calling a separate service function is indicated by lighting of the

[

TROUBLE

] LED.

BIT functions

During programming with a bit function, the LEDs 1 to 8 show the current setting of particular

parameters (diode on – YES, off – NO). Pressing the keys [1] to [8] changes the state of the

corresponding diode. The state of 8 parameters is confirmed with the [#] key. If the

programming function includes more parameters, the control panel will signal with two short

beeps acceptance of the first eight parameters and the LEDs 1 to 8 will display the state of

the next group of eight. The control panel shows on the

[

ALARM

AB]

and

[

ARMED

AB]

LEDs the set of options being currently programmed. When all the parameters have been

programmed, the control panel will signal exiting the function with four short beeps and a long

one.

The [

] key makes it possible to quit the function at any time without saving the changes in

currently displayed data.

DEC functions

During programming the LEDs 1-4 show the first digit (binary), LEDs 5-8 - the second digit,

while the LEDs AB, AB display the counter of digit pairs (binary). The programming consists

in entering a two-digit number and confirming it with the [#] key. The control panel will confirm

operation with two short beeps. When all the parameters have been programmed, the control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info